definitive technology

slash32487 · Post by **slash32487** » Sat Feb 11, 2017 10:02 am

1. Device: definitive technology solocinema studio
2. Type of device: AV Receiver
3. Year: 2016
4. JP1/UEI Remote model: Nevo 2
5. Do you have a JP1 cable? Yes
6. Still have original remote? Yes
7. Checked the file section? Yes
8. Checked Pronto file section (at R/C)? Yes
9. Partially working setup code? No
10. Learning remote question? Yes
11. Have you tried the JP1 Lookup Tool? Yes, didn't find anything
12. If you have a Nevo (or similar) remote, have you tried ez-rc.com? n/a

Post by **The Robman** » Sat Feb 11, 2017 10:04 am

As you have a Nevo, why did you enter "n/a" for question 12?

slash32487 · Post by **slash32487** » Sat Feb 11, 2017 10:08 am

im new to this forum and RM. i read on a forum that if my Tivo slide remote isnt doing the job i should get the nevo because it should work. my tivo slide works with the learning feature for the volume up and down but it will not work with the power for the def tech soundbar. i tried the same with the nevo and it isnt working either or i do not know what i am doing

slash32487 · Post by **slash32487** » Sat Feb 11, 2017 10:09 am

i cannot register to ez-rc.com it wont let me get in. unless you have a login for me

mdavej · Post by **mdavej** » Sat Feb 11, 2017 5:39 pm

See this note about ez-rc. If you still have trouble, download Remote Master.

http://www.hifi-remote.com/wiki/index.p ... rogramming

Here is the device upgrade file for your soundbar from ez-rc. You can load it into your remote and setup your volume punch thru entirely in Remote Master without using ez-rc. The link above also has tutorials and instructions for that.

https://www.hifi-remote.com/forums/dload ... e_id=14395

Here is a very good Tivo file for you as well:

https://www.hifi-remote.com/forums/dload ... e_id=13879

Advanced user's here may have an interest in this soundbar's new protocol.

slash32487 · Post by **slash32487** » Sat Feb 11, 2017 6:38 pm

ok i figured out how to get onto ez-rc and now my device wont stay connected so i went to the regedit and did the change but the site wont stay connected so when i try to download to the remote it doesnt take. im on windows 10. i tried also installing urc8602 but i got an error "Error accessing the registry"

i also tried to be fast when hitting the buttons on the computer it worked to upgrade the firmware but isnt holding to download the info to the remote. i keep getting this pop up Please connect your remote to the PC via the USB cable, and press OK below.

The USB connection may take up to 5 seconds to be ready.

mdavej · Post by **mdavej** » Sat Feb 11, 2017 7:09 pm

The regedit will definitely fix the connection issue. Just unplug and replug after the edit. There could also be more than one folder. Make sure you get them all (every one that starts with VID_06E7 and every one named Xsight something). This key name also changes slightly after a successful firmware update, so you have to do the regedit again.

If you've never connected to ez-rc before, you also need to download and install the Conduit program if you don't see it running in the tray. Conduit isn't needed for Remote Master. And again, you can load the file I made for you without ez-rc at all.

slash32487 · Post by **slash32487** » Sat Feb 11, 2017 7:53 pm

now the remote stays connected but the app cuts out midway. starts to update with the window on the bottom and then the "Please connect your remote to the PC via the USB cable, and press OK below.

The USB connection may take up to 5 seconds to be ready." pop up comes up after 3 seconds

mdavej · Post by **mdavej** » Sat Feb 11, 2017 8:08 pm

Unplug at that point, fix the registry again and plug back in. Make sure your batteries are still good as well.

If the remote is stuck in update mode, try number 10 here:
https://www.hifi-remote.com/forums/viewt ... 7215#p27215

slash32487 · Post by **slash32487** » Sun Feb 12, 2017 12:39 am

i installed windows 7 on a partition to see if it was the computer but it looks like it could be the remote. keeps bouncing out mid update and asks me to plug in the remote but the remote itself still says usb on the screen

is there a tutorial on how to install the latest firmware on RM for the nevo c2

slash32487 · Post by **slash32487** » Sun Feb 12, 2017 8:41 am

i have been reading more and it seams like only way to upgrade firmware is through ezrc

here is a video of what happens to me.
http://sendvid.com/1zke396j

im not sure how to use RM but im going to try that out now

mdavej · Post by **mdavej** » Sun Feb 12, 2017 10:52 am

Also change the key under Xsight_Color, unplug/replug and try again. And try "start a new setup".

From your keys, it appears that you have the latest firmware already and don't need to use ez-rc anymore. On the remote go to Home, Settings, About and see if it's 1.3.33 for a Nevo or 1.3.32 for an Xsight.

slash32487 · Post by **slash32487** » Mon Feb 13, 2017 8:24 am

used RM got the codes to run. then i did learning from nevo c2 to my tivo slide remote for the on/off feature that wasnt working from the def tech remote to tivo and that worked. the nevo isnt for me but very happy it did the job i wanted in the end.