The new Radio shack remote, it is HD TV remote, the 15-135, $19.95.
It takes 5 digit setup codes and 5 digit EFC's. It is a learning remote, and is marked jp1.3 on the PC board. Unlike the 15-100, the pins are in plain sight. And unlike the 15-100, this remote stinks. Keys are too small, and feel like they're even with the case. No backlighting,
Speaking of the 15-100, its on sale for $19.99.
New radio shack remote; 15-135
Moderator: Moderators
New radio shack remote; 15-135
Last edited by MaskedMan on Wed Apr 02, 2008 11:02 pm, edited 1 time in total.
Edmund
Now that it's on sale for $14.99, it's not so bad. I picked it up just to have another JP1.3 to play with. But it's actually starting to grow on me. MaskedMan correctly pointed out it's flaws, but for $15 I can overlook most of them. It does have a few things going for it:
- Tons of buttons (more than my 8910)
Tons of codes (even DirecTV and my new Toshiba DVD-R)
Tons of memory (double the move/macro, upgrade and learning of an 8910)
Small and light
Learning
Shift key is not recessed
Last edited by mdavej on Fri Nov 21, 2008 1:19 pm, edited 3 times in total.
Radioshack 15-135 and jp1.3
Hi,
I am newbie to this forum. I just bought the 15-135 figuring like you that for $16 it's fun to play around with. If you are thinking on making some files for this I would really appreciate a copy. Also I ordered the JP1 "contact less" cable from eBay. This device seems to have jp1.3 does that work with a jp1 cable and "remote master" or is it a whole new ball of wax? I can easily build a jp1.2 serial cable as shown in this forum. Would that have a better chance of success? The problem I face is that I have bunch of no-standard equipment to control. The TV is a Viewsonic N2750W for which nobody seems to have codes. Then I have a hi-sense (DB2020) HDTV receiver which also seems to have no standard code. Finally an Emerson DVD player MVD2042. So the only way out I see is to use the original remotes to gather the codes and then teach them to this device. If this device is not suitable, I would appreciate a recommendation for an alternative. As long as it does not involve a lot of money.
Thanks for your help
I am newbie to this forum. I just bought the 15-135 figuring like you that for $16 it's fun to play around with. If you are thinking on making some files for this I would really appreciate a copy. Also I ordered the JP1 "contact less" cable from eBay. This device seems to have jp1.3 does that work with a jp1 cable and "remote master" or is it a whole new ball of wax? I can easily build a jp1.2 serial cable as shown in this forum. Would that have a better chance of success? The problem I face is that I have bunch of no-standard equipment to control. The TV is a Viewsonic N2750W for which nobody seems to have codes. Then I have a hi-sense (DB2020) HDTV receiver which also seems to have no standard code. Finally an Emerson DVD player MVD2042. So the only way out I see is to use the original remotes to gather the codes and then teach them to this device. If this device is not suitable, I would appreciate a recommendation for an alternative. As long as it does not involve a lot of money.
Thanks for your help
If you could link the cable you bought that would help but most likely no. A jp1.3 device requires a cable that would usually be referred to as a jp1.x or jp1.2 cable. If it's a parallel cable then it definitely won't work. There has never been a parallel cable design for jp1.x remotes.
The jp1.2 serial cable should work great and since it's a learning remote getting it to control your devices shouldn't be a problem.
The jp1.2 serial cable should work great and since it's a learning remote getting it to control your devices shouldn't be a problem.
mdavej
I bought a couple of the 15-135s today for $10 each. I do not have a serial port on my new compaq notebook. Is there a USB cable I can use to program this remote?
I am a beginner, so I know I need to look the forum over for the necessary reads, but right now I am wondering what the difference is between a JP1, JP1.1, etc.
I downloaded your RDF but I am a long way from upgrades.
I bought a couple of the 15-135s today for $10 each. I do not have a serial port on my new compaq notebook. Is there a USB cable I can use to program this remote?
I am a beginner, so I know I need to look the forum over for the necessary reads, but right now I am wondering what the difference is between a JP1, JP1.1, etc.
I downloaded your RDF but I am a long way from upgrades.
Sidiko!
You need THIS JP1.3 cable. All you really need to know as a beginner is that older remotes are JP1, newer ones are 1.1 (rare), 1.2 or 1.3 (collectively 1.x). JP1 and 1.x require different cables, but all use the same software tools - IR, RM, KM. JP1 is also a very broad term applied to any remote these tools interface with. Since the cable is your biggest investment (more than your remotes in this case), once you go down the 1.3 path, you'll probably want to stick with those. Luckily most new JP1 remotes are JP1.2 or 1.3, both of which will work with your cable for years to come. Just search the forums for more details.
Also, the standard connector is too big to fit the 135. You may opt for a more expensive cable with a smaller connector (just tell the vendor), or simply remove the outer clip from the standard connector yourself.
You can also do quite a bit without JP1. Check out Rob's wonderful MANUAL to use learning, key moves, advanced codes and macros right away. A quick reference updated for the 135 is available HERE.
Also, the standard connector is too big to fit the 135. You may opt for a more expensive cable with a smaller connector (just tell the vendor), or simply remove the outer clip from the standard connector yourself.
You can also do quite a bit without JP1. Check out Rob's wonderful MANUAL to use learning, key moves, advanced codes and macros right away. A quick reference updated for the 135 is available HERE.
Hey, thanks a lot. I will check all of the links you provided right now.
Also, one or two other forum members have given me suggestions on what to read first.
I just "road tested" the remote, and by following the directions in the book, I have been UNsuccessful in controlling my Sony GX-330 DVD recorder. Also, can't control my Harmon Kardon AV receiver either. Unexpectedly, I turned off/on my RCA laserdisk player and my RCA TV while scrolling through codes "searching" for a code that would control the DVD recorder.
Also, one or two other forum members have given me suggestions on what to read first.
I just "road tested" the remote, and by following the directions in the book, I have been UNsuccessful in controlling my Sony GX-330 DVD recorder. Also, can't control my Harmon Kardon AV receiver either. Unexpectedly, I turned off/on my RCA laserdisk player and my RCA TV while scrolling through codes "searching" for a code that would control the DVD recorder.
Sidiko!
Trouble using the 15-135
mdavej,
I tried using the pregramming link for my 15-135 and I could not program it to control my Sony DVD recorder, even after I read it needed to be programmed "under" a VCR key. I searched for the codes after entering manually. I am striking out big time.
What do I need to read to implement some of the upgrades or even see in any of my entertainment equipment remote codes are known to use these tools?
I tried using the pregramming link for my 15-135 and I could not program it to control my Sony DVD recorder, even after I read it needed to be programmed "under" a VCR key. I searched for the codes after entering manually. I am striking out big time.
What do I need to read to implement some of the upgrades or even see in any of my entertainment equipment remote codes are known to use these tools?
Sidiko!
A
If you want to try using a built in code. you might have a better chance with the Sony GX-330 by changing the DVD recorder's command mode to DVD1. There are very few remote models with the default DVD3 mode, but plenty with DVD1 mode built in. Of course, when you get your JP1.x cable, it doesn't matter so much.
It doesn't look like the 15-135 has a built in setup code for the HK receiver, but HK is fairly consistant about the ir codes they use so you should be able to find an upgrade file that you can start with. However, make sure you use an upgrade file that uses "NEC 4 Device Combo", not "HK Combo". HK Combo is essentially NEC 2 DEV Combo with the first device as 128.112 and second device as 130.114. It was created before there were NEC Combo protocols, and will either require a protocol upgrade, or RM will complain that there is no protocol upgrade for your remote, depending on the remote (I think in case of JP1.3 remote, it will be the former).
It doesn't look like the 15-135 has a built in setup code for the HK receiver, but HK is fairly consistant about the ir codes they use so you should be able to find an upgrade file that you can start with. However, make sure you use an upgrade file that uses "NEC 4 Device Combo", not "HK Combo". HK Combo is essentially NEC 2 DEV Combo with the first device as 128.112 and second device as 130.114. It was created before there were NEC Combo protocols, and will either require a protocol upgrade, or RM will complain that there is no protocol upgrade for your remote, depending on the remote (I think in case of JP1.3 remote, it will be the former).
If these sony codes 20533, 21533, 20864, 20772, 21033, 21431, 21516 or the harmon kardon code 31289 doesn't work, you can either learn the buttons for each, or wait until you get a cable. Once you have a cable, there are several upgrades on this site you can try. And if they don't work, it's easy to make your own. Don't dispair.
You can get a head start by reading THIS, as well as most of the stickies in the beginner's forum. You'll need Remote Master, a.k.a. RM to build your upgrades, and IR to program the remote. Both are available from the Tools folder in the File section.
And the sony doesn't have to be under a VCR key. It can be on any device key on this remote. The first number in the code dictates the device type. Your code search in the 2xxxx range shouldn't have affected your TV. Although some of the older help docs on this site talk about 4 digit codes, you need to make sure you use 5.
You can get a head start by reading THIS, as well as most of the stickies in the beginner's forum. You'll need Remote Master, a.k.a. RM to build your upgrades, and IR to program the remote. Both are available from the Tools folder in the File section.
And the sony doesn't have to be under a VCR key. It can be on any device key on this remote. The first number in the code dictates the device type. Your code search in the 2xxxx range shouldn't have affected your TV. Although some of the older help docs on this site talk about 4 digit codes, you need to make sure you use 5.
-
vickyg2003
- Site Admin
- Posts: 7109
- Joined: Sat Mar 20, 2004 12:19 pm
- Location: Florida
- Contact:
I have this remote also. I've tried the DVD code 21070 that vickyg mentioned and the 15-135 would not accept it.
I rather like the remote alot. I like small buttons on a remote and it doesn't seem like the buttons are flush to the remote. They are elevated some, even as high as the buttons on my 10820.
I am also awaiting my USB JP1.2/3 cable from Tommy. Just make sure you tell him that you want that smaller IDC connector for an extra $5 if you want to use his cable for the 15-135.
I rather like the remote alot. I like small buttons on a remote and it doesn't seem like the buttons are flush to the remote. They are elevated some, even as high as the buttons on my 10820.
I am also awaiting my USB JP1.2/3 cable from Tommy. Just make sure you tell him that you want that smaller IDC connector for an extra $5 if you want to use his cable for the 15-135.
OK, I set my GX-330 to DVD1 per "kupakai." Codes did not work in the -135 at first. Then I searched, found it. 20533. But hey, that was my first manually input code. Must have fumbled with the buttons.
CANNOT PAUSE RECORD. CAN'T EVEN STOP RECORD ONCE BEGUN WITH THE -135. But, maybe a shift operation involved? I see 2 keys that look like dual use, but nothing in the manual about it!
But, I have a cable on order from Tommy.
And a lot of reading and learning ahead.
mattg568, what was up with you trying vickyg? Just fooling around or do you have a Sony GX-330 DVD recorder too?
Gonna see if I can program a macro now, maybe see what advanced codes are all about. Anybody got a link describing advanced codes?
CANNOT PAUSE RECORD. CAN'T EVEN STOP RECORD ONCE BEGUN WITH THE -135. But, maybe a shift operation involved? I see 2 keys that look like dual use, but nothing in the manual about it!
But, I have a cable on order from Tommy.
And a lot of reading and learning ahead.
mattg568, what was up with you trying vickyg? Just fooling around or do you have a Sony GX-330 DVD recorder too?
Gonna see if I can program a macro now, maybe see what advanced codes are all about. Anybody got a link describing advanced codes?
Sidiko!