View previous topic :: View next topic |
Author |
Message |
slocko
Joined: 28 Nov 2003 Posts: 25
|
Posted: Fri Nov 28, 2003 1:52 pm Post subject: Any quick hits on this device? |
|
|
NEC1 (2 device), device 182, subdevice 88 ??
Thanks. _________________ still learning......... |
|
Back to top |
|
|
jamesgammel Exile Island Resident
Joined: 03 Aug 2003 Posts: 394 Location: Gillette, Wyoming |
Posted: Fri Nov 28, 2003 2:14 pm Post subject: |
|
|
Slocko,
You didn't even mention for which remote . Devices.xls lists Nec 1, device 88 as CD_0155. (you might find some usable efc's.). Nec1, device 182 is CD_0190. I didn't find any in Devices.xls listing BOTH in one.
Jim |
|
Back to top |
|
|
johnsfine Site Admin
Joined: 10 Aug 2003 Posts: 4766 Location: Bedford, MA |
Posted: Fri Nov 28, 2003 2:18 pm Post subject: Re: Any quick hits on this device? |
|
|
slocko wrote: | NEC1 (2 device), device 182, subdevice 88 ?? |
I think there is no built in setup code.
Since you were able to decode that, I assume you can download learned signals. So why worry about built in setup codes. Just make an upgrade. |
|
Back to top |
|
|
Mark Pierson Expert
Joined: 03 Aug 2003 Posts: 3017 Location: Connecticut, USA |
Posted: Fri Nov 28, 2003 3:47 pm Post subject: |
|
|
I couldn't locate any existing code either. As John said, you should be able to learn and decode all your functions in IR, and then create your own upgrade with KM or RM. _________________ Mark |
|
Back to top |
|
|
slocko
Joined: 28 Nov 2003 Posts: 25
|
Posted: Fri Nov 28, 2003 5:00 pm Post subject: |
|
|
sorry. the signals were learned on a 2116. thanks. I am beginning to understand it a little better now. I will try 190 and 155. eventually i will study the materials to create the upgrade. _________________ still learning......... |
|
Back to top |
|
|
johnsfine Site Admin
Joined: 10 Aug 2003 Posts: 4766 Location: Bedford, MA |
Posted: Fri Nov 28, 2003 5:20 pm Post subject: |
|
|
slocko wrote: | I will try 190 and 155. eventually i will study the materials to create the upgrade. |
The device and subdevice numbers must match exactly for a signal to work at all, so there's no reason to test ones that just come close. Occasionaly a setup code with the same device and a different subdevice may be related enough to give you hints about discrete codes or other signals missing from your original remote, but first you must do the basics of creating an upgrade based on your learned signals. |
|
Back to top |
|
|
jamesgammel Exile Island Resident
Joined: 03 Aug 2003 Posts: 394 Location: Gillette, Wyoming |
Posted: Fri Nov 28, 2003 6:08 pm Post subject: |
|
|
I think he meant he'd try setup code CD_0190 and CD_0155, not substitute 190 and 155 for the device codes. For some reason he's trying to avoid making an upgrade with the two device codes he needs. In the long run, that'll prove to be the major error. Comon slocko, zip up your zipper, tie your shoes and just make that upgrade, it isn't THAT difficult. Besides, you got all of us to lend a hand if you run into a stumbling block.
Jim |
|
Back to top |
|
|
Mark Pierson Expert
Joined: 03 Aug 2003 Posts: 3017 Location: Connecticut, USA |
Posted: Fri Nov 28, 2003 6:34 pm Post subject: |
|
|
jamesgammel wrote: | I think he meant he'd try setup code CD_0190 and CD_0155, not substitute 190 and 155 for the device codes. |
John was pointing out that trying those 2 setup codes would likely be fruitless since the device probably requires both the Device and Sub-Device to function. The time involved would be better spent doing the ol' JP1 learn-decode-make-upgrade! 8) _________________ Mark |
|
Back to top |
|
|
slocko
Joined: 28 Nov 2003 Posts: 25
|
Posted: Mon Dec 01, 2003 4:53 pm Post subject: |
|
|
okay. since you guys are rabid preachers always trying to convert people, I decided to give the upgrade a try
i find the beginners document too technical for beginners, but it's better than nothing i suppose. maybe one day i will re-write it.
i learned about half the commands and copied the efc codes from the learned section in IR to keymaster. I chose cd device, and the same parameters listed in IR. for device number i incremente by 1000 to 1090. as i write this, i realize that it should be 1190. i have to try that when i get home.
i successfully copied the upgrade code into IR. keymaster did not generate any protocol information which i assume is because the protocol is already supported by the 2116.
it didn't work. any ideas assuming using 1090 is not the problem?
if i don't have any luck tonight, i will upload the file and you guys can take a look.
is there any reason that IR doesn't store it's values in an ini file format? if it did, it would be simple for KM via vba to update the ini file with the relevant information that would load into IR when you run it. no cutting and pasting. maybe a future release? _________________ still learning......... |
|
Back to top |
|
|
Nils_Ekberg Expert
Joined: 02 Aug 2003 Posts: 1689 Location: Near Albany, NY |
Posted: Mon Dec 01, 2003 5:15 pm Post subject: |
|
|
This may be a silly question but did you assign the upgrade to a device button on the setup panel after you pasted it in? I ask this question alot since nobody ever mentions that they did that between "pasting" and "uploading".
You probably did so the best bet is to post the IR and KM files in jp1 diagnostics. We will need to see the upgrade and the learned buttons in IR _________________ Nils
Files Section
Diagnosis File Section |
|
Back to top |
|
|
johnsfine Site Admin
Joined: 10 Aug 2003 Posts: 4766 Location: Bedford, MA |
Posted: Mon Dec 01, 2003 6:56 pm Post subject: |
|
|
slocko wrote: | for device number i incremente by 1000 to 1090. |
I expect you mean that you increased the setup code number not the "device" number.
The setup code number barely matters at all. Any number (within the range of valid numbers) will work. You only need to avoid using the exact number of another setup code that you're also using.
And as Jim said you need to change one of the device modes on IR's setup tab to use whatever setup code (type and number) you chose and installed. |
|
Back to top |
|
|
johnsfine Site Admin
Joined: 10 Aug 2003 Posts: 4766 Location: Bedford, MA |
Posted: Mon Dec 01, 2003 7:06 pm Post subject: |
|
|
slocko wrote: |
is there any reason that IR doesn't store it's values in an ini file format? if it did, it would be simple for KM via vba to update the ini file with the relevant information that would load into IR when you run it. no cutting and pasting. maybe a future release? |
IR stores its files in a simple text file, which can be modified by any program that can read its model-specific structure from an RDF file. KM doesn't use RDF files and no one has written an RDF file parser in VBA (just Pascal, Java, and C++) so it would be a hard change to KM.
It would be a much easier change in RemoteMaster (a KM alternative that uses RDF files already). We might even get around to that at some point. But most of the inconvenience comes from the fact that RM vs. IR is two programs at all, not from the particular choice of boundary. It wouldn't be much easier to have RM change your IR txt file but then need to reopen that file in IR in order to send it to the remote. Having RM be able to talk directly to the JP1 cable would be better but is further away. |
|
Back to top |
|
|
slocko
Joined: 28 Nov 2003 Posts: 25
|
Posted: Mon Dec 01, 2003 9:56 pm Post subject: |
|
|
we have blast off!!!!!!!!!!
wow, this was so much easier than it looks.
turns out that i had the obcs and efcs confused. so didn't look carefully in IR and was plugging in obc values instead of efc values.
thanks a bunch!!!!!!!!!!!!!!!! _________________ still learning......... |
|
Back to top |
|
|
slocko
Joined: 28 Nov 2003 Posts: 25
|
Posted: Tue Dec 02, 2003 9:23 am Post subject: |
|
|
I have one more question.
Is there anyway to make a macro into a function assigned to a key without taking up key move space?
In other words, can I create an upgrade device and map all the macro keys as one function and come up with an EFC for it? This way, the memory is taken up by the upgrade area, and not the macro/keymove space. sort of like learning 3 key presses as one learned key press. i haven't tried that with learning, but it should be possible. _________________ still learning......... |
|
Back to top |
|
|
Mark Pierson Expert
Joined: 03 Aug 2003 Posts: 3017 Location: Connecticut, USA |
Posted: Tue Dec 02, 2003 9:33 am Post subject: |
|
|
slocko wrote: | Is there anyway to make a macro into a function assigned to a key without taking up key move space? |
In a word, no.
You might want to explore an extender (if there's one available for your remote) so that you can get significantly more key move/macro space. _________________ Mark |
|
Back to top |
|
|
|