View previous topic :: View next topic |
Author |
Message |
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21251 Location: Chicago, IL |
Posted: Tue May 15, 2012 11:14 am Post subject: |
|
|
tranx wrote: | I shall look for an upgrade library and see if my devices are already there. |
At the top of this page is a link to the File Section, from there you would follow the link to the Device Upgrades folder, which has separate sub-folders for each "type" of device (ie, TV, DVD, VCR, etc) _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
tranx
Joined: 13 May 2012 Posts: 682 Location: Hants, UK |
Posted: Tue May 15, 2012 1:10 pm Post subject: |
|
|
Right, thank you Rob - a good selection but may eventually be able to contribute something. Just ordered Atlas OCAP URC-1056B01 too, so there will be plenty to play with while trying to understand things.
Regards
Chris |
|
Back to top |
|
|
underquark Expert
Joined: 20 Jun 2005 Posts: 874 Location: UK |
Posted: Wed Jun 06, 2012 4:26 am Post subject: FTDI interface for cheapskates |
|
|
Thank's, as ever, Tommy for your work.
6-pin plugs seem hard to come by in the UK. I found one source selling them for £0.30 per unit plus £2.40 postage for orders up to the value of £50 but I couldn’t tell if that included contacts or what the minimum purchase quantity was and I was too lazy to e-mail them. Previously I have just hacked the end off a 40-wire HDD cable but on this occasion I ordered a FTDI cable with the 6-in-a-row connector attached (it was actually cheaper than the wire-ended one). I cut it in half, re-arranged the wires and made myself a connector. No 2 x 3 connector, co crimps etc. needed.
Quote: | Preferably mount the connector in a small vice or clamp or, at least, on a flat and well-lit surface.
Orientate the connector with cable to your left, contact openings to your right, black wire furthest away from you.
Grasp the Orange wire and gently push it to your right to reveal a small gap between the plastic retainer on the connector housing and the metal contact. Insert a thin, pointed probe (or slightly blunt needle or bodkin or even a toothpick) into the gap, under the plastic retainer and carefully lever it up whilst gently pulling on the wire as you do so . There will be two "bumps" of metal to overcome. This should allow the cable and contact to be withdrawn from the connector housing.
Repeat for the Yellow wire and for the Red wire and their contacts.
Cut the Brown wire flush with its contact (and just leave the contact in the connector housing).
Cut the Red wire off its contact.
Retract and insulate the Red and Brown wires.
Cut through the channel in the connector housing that had been occupied by the Red wire and contact to split the connector into two (not equal-sized) pieces.
Insert the Yellow wire and contact where the Orange one used to be.
Insert the Orange wire and contact where the Yellow one was.
Place the smaller piece of connector over the larger so that the Black wire and contact line up with the middle hole (now containing the Orange wire). Glue in place. Trim any rough edges. |
Link to How To document.
Last edited by underquark on Thu Jun 07, 2012 6:05 pm; edited 1 time in total |
|
Back to top |
|
|
underquark Expert
Joined: 20 Jun 2005 Posts: 874 Location: UK |
Posted: Thu Jun 07, 2012 11:42 am Post subject: |
|
|
For information for any UK JP1-ers, I bought this item from a good eBay seller for £13.08 including postage. After hacking it as described, above, it's working well using IR7 in Windows XP. (I'll get around to trying it with a more up-to-date version of IR or RMIR in linux it's just that's what I have running on my machine that I tried it on).
Post Office decided the package was just too big to squeeze through their template and charged me extra but the seller refunded this immediately I told him so worth buying from him if you're in the UK/Europe and interested in the 6-in-a-row plugged cable like I used. |
|
Back to top |
|
|
sloppyedwards
Joined: 12 Jun 2012 Posts: 6
|
Posted: Thu Jun 14, 2012 4:05 pm Post subject: Re: FTDI interface for cheapskates |
|
|
underquark wrote: | I ordered a FTDI cable with the 6-in-a-row connector attached (it was actually cheaper than the wire-ended one). I cut it in half, re-arranged the wires and made myself a connector. No 2 x 3 connector, co crimps etc. needed. | Brilliant! I may try the same thing with this cable: http://www.foogra.com/products/43394/ |
|
Back to top |
|
|
dre
Joined: 03 Jan 2005 Posts: 22
|
|
Back to top |
|
|
mdavej Expert
Joined: 08 Oct 2003 Posts: 4502
|
Posted: Fri Jun 15, 2012 8:43 am Post subject: |
|
|
Great find. Would you mind posting the pin-out for that cable? |
|
Back to top |
|
|
cauer29
Joined: 03 Feb 2010 Posts: 236
|
Posted: Sat Jun 23, 2012 11:15 am Post subject: |
|
|
FWIW about a year ago I purchased the same cable but with a 6 pin single row connector and released the pins from the connector housing and installed them into a 2 x 3 connector housing in the appropriate JP1 arrangement. No need to purchase pins and crimp them onto the wires. It works fine as expected.
This is the cable I purchased:
http://www.digikey.com/product-detail/en/TTL-232R-3V3/768-1015-ND/1836393 |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21251 Location: Chicago, IL |
Posted: Sat Jun 23, 2012 1:43 pm Post subject: |
|
|
The reason that Tommy is telling people to use crimps, etc now is in order to make a connector that's much smaller than the traditional IDC connectors that we used to use. This is because UEI is making much smaller openings for the 6-pin these days. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
underquark Expert
Joined: 20 Jun 2005 Posts: 874 Location: UK |
Posted: Sat Jun 23, 2012 1:55 pm Post subject: |
|
|
You ain't gonna get much smaller than my connector - it's got a corner missing, for a start. I had an idea to glue a matchstick-sized rod to that corner to facilitate insertion and removal of the connector. |
|
Back to top |
|
|
cauer29
Joined: 03 Feb 2010 Posts: 236
|
Posted: Sat Jun 23, 2012 8:31 pm Post subject: |
|
|
The Robman wrote: | The reason that Tommy is telling people to use crimps, etc now is in order to make a connector that's much smaller than the traditional IDC connectors that we used to use. This is because UEI is making much smaller openings for the 6-pin these days. |
No issue there. I'm using a connector housing that is the same size as the one Tommy said to use. I simply lifted the release tab on each pin position of the 1x6 non-IDC connector that came on the cable, slid pin/wire combos out the back end and inserted them into the 2x3 non-IDC connector housing. As I said, no crimping needed. No use of IDC anything.
In a pinch, you could cut the 1x6 connector housing on the cable that I linked, into 2 pieces. You lose one position in the cutting. So, you'd end up with a 2 position 1 row connector housing and a 3 position 1 row housing. You only need 4 pins total, a 3 position and a 1 position would work. Super glue them back to back, poke the wire/pin combos in and you're done. |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21251 Location: Chicago, IL |
Posted: Sat Jun 23, 2012 10:18 pm Post subject: |
|
|
cauer29 wrote: | I'm using a connector housing that is the same size as the one Tommy said to use. I simply lifted the release tab on each pin position of the 1x6 non-IDC connector that came on the cable, slid pin/wire combos out the back end and inserted them into the 2x3 non-IDC connector housing. As I said, no crimping needed. No use of IDC anything. |
Do you have pics or part numbers that would help me visualize what you're doing? _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
cauer29
Joined: 03 Feb 2010 Posts: 236
|
Posted: Sat Jun 23, 2012 11:27 pm Post subject: |
|
|
The Robman wrote: | cauer29 wrote: | I'm using a connector housing that is the same size as the one Tommy said to use. I simply lifted the release tab on each pin position of the 1x6 non-IDC connector that came on the cable, slid pin/wire combos out the back end and inserted them into the 2x3 non-IDC connector housing. As I said, no crimping needed. No use of IDC anything. |
Do you have pics or part numbers that would help me visualize what you're doing? |
Here's the cable that I purchased. It is a variant of the one Tommy says to buy. The only difference is that this one has a 6 position single row connector vs bare wires on the Tommy version.
The FTDI part number for the cable that I purchased is:
TTL-232R-3V3 (digikey 768-1015-ND)
The one Tommy says to get is identical but it has raw wire ends rather than a 6 x 1 connector.
TTL-232R-3V3-WE (digikey 768-1016-ND)
The "WE" means wire ends. It looks like this:
If you look carefully at the 6 x 1 connector on the cable that I purchased, you can see a little tiny plastic flap on the connector housing for each pin. You lift the flap for a pin and pull back on the wire. The wire with crimped pin attached slides out the back of the connector.
Here's a picture showing the flaps:
Do this for all six pins. Install the 4 required wires with already crimped pins into the exact same 2 x 3 connector housing that Tommy says to use, following his instructions for which wire color goes to which position.
edit: turns out it's not the exact same connector but one that is very similar:
Digikey 609-2380-ND FCI 69176-006LF. I didn't bother to purchase the connector, but just harvested the connector from an old computer case.
In the end, you have a cable that is 100% physically identical to what you would have following Tommy's instruction completely. The only difference is that you didn't need to buy any crimp pins and you didn't need to crimp them to the bare wires. You need only a modicum of dexterity to extract the pins with wires attached, from the 6 x 1 connector. Then again if you go the Tommy route, you have to have the skill to crimp the pins onto the bare wires. I personally think that my method is less work, less money and less skill required. |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21251 Location: Chicago, IL |
Posted: Sun Jun 24, 2012 11:48 am Post subject: |
|
|
I like it, thanks for posting. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21251 Location: Chicago, IL |
|
Back to top |
|
|
|