View previous topic :: View next topic |
Author |
Message |
houdini
Joined: 18 Jan 2007 Posts: 37
|
Posted: Thu Jan 18, 2007 9:21 am Post subject: Need Codes for Captiveworks cw-1000 fta/pvr box for Slingbox |
|
|
I have one of the new captiveworks cw-1000 fta/pvr boxes. I haven't been able to create a bin for the slingbox to use. Captiveworks has released a pronto type of file at
http://captiveworks.org/forum/comments.php?CommentID=1423&&Download=cw-1000_remote_codes_pronto_format.zip
I have slingbox ir blaster version 2.0 JU.
I've tried working with decodeccf and rm but can't seem to figure it out. I don't know how to convert this pronto to a useable bin for slingbox. Can anyone help me out on this or point me in the right direction? Thanks |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21248 Location: Chicago, IL |
|
Back to top |
|
|
houdini
Joined: 18 Jan 2007 Posts: 37
|
Posted: Thu Jan 18, 2007 5:40 pm Post subject: |
|
|
I took the KM file, loaded it in RM, switched to the slingbox JU remote, mapped the buttons, and exported as a raw bin file. I put this in my sbav folder and went into the slingbox setup. I selected other under sat/fta receivers and entered the new code. I entered V2000 (because the exported bin file in the sbav folder is V2000_JU.bin) and it said the slingbox cannot load the IR code you selected.
Is this not what I was suppose to try? Did I miss something here? |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21248 Location: Chicago, IL |
Posted: Thu Jan 18, 2007 6:02 pm Post subject: |
|
|
While the code is loaded into RM, try changing the device mode to SAT, which should cause the binary file created to be S2000_JU.bin, and then try proceeding with that file.
Are you 100% positive that you have one of the old JU boxes? You might want to create a PL file also. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
houdini
Joined: 18 Jan 2007 Posts: 37
|
Posted: Thu Jan 18, 2007 7:24 pm Post subject: |
|
|
Ok. My slingbox reports IR blaster 2 and not 2.1 I thought that should mean it is JU versus PL but I tried PL and the file loaded ok in slingplayer setup. I've tried it as a SAT and a DVR (S2000, V2000). Both load up fine in slingplayer but the power test button does nothing. I tried fast, medium and slow on both and have two heads of the ir blaster on top and bottom of the cw1000. Even though the power button test did nothing, I tested the other buttons in slingplayer after the setup. I got nothing. Any ideas?
Also, I know my slingbox is working correctly with the 4 headed IR blaster because it is controlling my moto moxi dvr just fine. |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21248 Location: Chicago, IL |
Posted: Thu Jan 18, 2007 7:59 pm Post subject: |
|
|
I had to create a new executor (aka Protocol) for the upgrade that I created, so let me try loading it into a remote to test it and if I spot anything wrong with it, I'll re-post it.
When you use the OEM remote, does the PVR respond to quick presses of the buttons or do you have to hold the buttons down for a little bit in order to get the box to respond? _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
houdini
Joined: 18 Jan 2007 Posts: 37
|
Posted: Thu Jan 18, 2007 8:08 pm Post subject: |
|
|
The box responds strangely to the oem remote. The ir has a narrow range so you have to point almost directly at the box. Normally you don't have to hold the buttons down long to get a response though. Normal button presses seem fine but while holding a channel up or volume up it doesn't always like to work. In other words..it would move the volume up 1 notch instead of going up until you let go. Sometimes it works as it should though. Again..that goes back to what I said about the box responding strangely to the oem remote. |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21248 Location: Chicago, IL |
Posted: Sat Jan 20, 2007 5:03 pm Post subject: |
|
|
I found the bug, it was in the fixed data. It was "00 08" but should have been "00 18". I have reloaded the file so you can try it again.
I have learned the signals using my Pronto and they match the ones posted exactly. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
houdini
Joined: 18 Jan 2007 Posts: 37
|
Posted: Sat Jan 20, 2007 7:40 pm Post subject: |
|
|
I created the slingbox PL bin and it worked perfectly! Thanks so much. You don't have a paypal account do you? I'd really like to send you a tip. |
|
Back to top |
|
|
The Robman Site Owner
Joined: 01 Aug 2003 Posts: 21248 Location: Chicago, IL |
Posted: Sat Jan 20, 2007 10:05 pm Post subject: |
|
|
houdini wrote: | I created the slingbox PL bin and it worked perfectly! Thanks so much. |
Glad it worked for you.
houdini wrote: | You don't have a paypal account do you? I'd really like to send you a tip. |
That's very generous. Sure I do, check the link in my sig. _________________ Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help! |
|
Back to top |
|
|
|