View previous topic :: View next topic |
Author |
Message |
stif
Joined: 02 Jun 2015 Posts: 21
|
Posted: Fri Nov 27, 2015 7:34 pm Post subject: control bresnan jp1.2. solved |
|
|
Hi
I need some help. , ihave an control bresnan on the board say. Atlas urc-1055ba0,,, conection say jp1.2. 6 pines. I tried using a prolific usb to serial. Db9 pin 5. To 3 jp1.x.
7 to pin 2
3 rx to 4. Or 6
2 tx to 4 or 6
Rmir say no control found
Ir8. Same
I tried interfase usb.serial
Bd 115200
And 9600
Prolific 2303
Waths is wrong.
Last edited by stif on Thu Dec 03, 2015 12:03 am; edited 1 time in total |
|
Back to top |
|
|
3FG Expert
Joined: 19 May 2009 Posts: 3368
|
|
Back to top |
|
|
stif
Joined: 02 Jun 2015 Posts: 21
|
Posted: Sat Nov 28, 2015 5:33 pm Post subject: |
|
|
thanks for helpme
i tried. and the same no control fpund
here model ci. or eeprom
The micro is marked SP553312Dwe,
9RD60DWE1025,
0L33R,
CTDP0532
may be isnt compatible jp1 or 2 i tried jp1 and no control found
is this ci eeprom compatible?
is the only one on the control |
|
Back to top |
|
|
3FG Expert
Joined: 19 May 2009 Posts: 3368
|
Posted: Sat Nov 28, 2015 7:23 pm Post subject: |
|
|
It the remote is labeled URC-1055 and the board says JP1.2, then it is a JP1.2 remote with a Motorola HCS08 processor. This remote uses flash memroy and does not use an EEPROM. It should work with the 2303 interface.
Please take the time to read the third link above (id=9507) and follow the instructions. Check and tell us if the remote is blinks in response to setting/clearing RTS. |
|
Back to top |
|
|
stif
Joined: 02 Jun 2015 Posts: 21
|
Posted: Sat Nov 28, 2015 9:11 pm Post subject: |
|
|
hi 3fg
the procesor isnt motorola or the ci has another number this is numbers of ic
SP553312Dwe,
9RD60DWE1025,
0L33R,
CTDP0532
all this numbers
i tried jp1.2
change rx tx 2 on3 3on 2 db9 output and nothi ng i try upload a picturde of board |
|
Back to top |
|
|
stif
Joined: 02 Jun 2015 Posts: 21
|
|
Back to top |
|
|
3FG Expert
Joined: 19 May 2009 Posts: 3368
|
Posted: Sun Nov 29, 2015 2:05 am Post subject: |
|
|
The board is telling you that the remote is a URC-1055. We know about that remote, and it will work with a functioning 2303 cable. Please follow Tommy Tyler's instructions to install RealTerm, and find out if toggling RTS (pin 5 on the JP1 connector) makes the remote blink twice. |
|
Back to top |
|
|
stif
Joined: 02 Jun 2015 Posts: 21
|
Posted: Sun Nov 29, 2015 5:54 pm Post subject: |
|
|
hi 3fg
icant do
never detect
ir with jp12dll original failed open jp1x interfase
with jp1x dll newer failed to read jp1x
jp1xtest original jp1x dll no jp1x co,mpatible found ...with newer dll a found jp1x compatible
signature 0000,memory ooo etc this say inclusive without control conecte
a found a post with same problem may be isnt jp12 compatible or fake jp12 this is post
http://www.hifi-remote.com/forums/viewtopic.php?t=5536
what you think is my control compatible or my cable serial is wrong
or conections |
|
Back to top |
|
|
stif
Joined: 02 Jun 2015 Posts: 21
|
Posted: Thu Dec 03, 2015 12:13 am Post subject: |
|
|
thanks to 3fg
the problem was prolific usb.cable try conwct from the output of serial ,, and this have a maxim ic rs232.
i conect to pin 1 3 5 and gnd.from prolific 2303hx and now is detected by ir software and jp1xtest |
|
Back to top |
|
|
|