JP1 Remotes

I have created a bin file for the Pioneer DVR with RM & get 3 gray out button. Anyone can help on this ?? Thanks.



Wayne

That means that you didn't assign any functions to those buttons. It's worth keeping in mind that Sling changes the names of buttons in the SBAV.cfg file depending on which "skin" you are using, whereas the RDF just has one fixed list of buttons. So, what you could do is make a note of the three button names in question, then go to SBAV.cfg and see what numbers those buttons use in the Sling world (and see if they're renamed for your device), then go to the RDF and see what button names correspond to those same button names. Then make sure that you have programmed the desired functions to those buttons.

In SBAV.cfg look for the [Keys] section and in the RDF look for the [Buttons] section.

For example...

in SBAV.cfg

[Keys]
...
048=SAP;;Misc
049=Surround;;Misc

[DVDP.Keys]
...
048=Subtitle;;Playback
049=Audio;;Playback

in the RDF...

[Buttons]
...
SAP/subtitle=48,
Surround=49,

In this case you will see that buttons 48 and 49 are called SAP and surround normally in the Slingbox and SAP/subtitle and Surround in the RDF, but if you just happen to be using a DVD recorder, the Sling changes the names to Subtitle and Audio.

Thanks, Rob.
Since the new version of Slingplyer,we are not able to open the SBAV.cfg any more !!


Wayne

I wasn't aware that the beta firmware has been made official already. I have just updated the main sticky post in the Slingbox forum to show what you need to do to use upgrades with the new software.

If your copy of SBAV.cfg was deleted when you upgraded to the new software, here's an archived copy...

https://www.hifi-remote.com/forums/dload ... le_id=2584

I'm using the "Pioneer_DVD_Recorder_DVR-520HS" file to created the Sling bin file & select "Pioneer" then "other" then the "created bin file" but still get grayed out button.
Perhaps that Pioneer skin by sling has keys missing ??

Wayne

What are the 3 greyed out buttons in question and which functions would you like assigned to them?

its "MENU","Page down","return" button. i just need the function as they should.

Wayne

There isn't a RETURN button in the version of SBAV.cfg that I'm looking at, so if you see that button on the screen, they must have added it since they changed the firmware.

Here are the relevant buttons from SBAV.cfg
033=DVD Menu
034=Setup Menu
035=Title Menu
036=Cancel
037=Clear
043=Page Up
044=Page Down

And here are the same buttons from the RDF
Menu=33,
Setup=34,
Guide=35,
Cancel=36,
exit=37,
Page+=43,
Page-=44,

Can you confirm that when you edited the upgrade file in RM that you assigned the relevant functions to these buttons, and then when you tested the upgrade with your Slingbox, the functions did not appear on those buttons?

Is this the button you are referring to as return?

It is the only button not mapped that I can see.
I think that would be commonly called replay.

The REPLAY button is defined for the PVR skin...

[PVR.Keys]
030=Skip;Quick Skip;Playback
031=Replay;Instant Replay;Playback

The generic buttons names for 30 and 31 are...

[Keys]
030=Skip+;Skip Forward;Playback
031=Skip-;Skip Backward;Playback

and in the RDF, those buttons are defined as...

[Buttons]
"next track":Skip+=30,
"prev track":Skip-=31,

Thanks a lot for all the inf.
I was look into the RDF in RM,all those grayed out buttons are assigned.
They just doesn't show up in Sling remote.
The "return" button is refer to the "_/__" button .
Is it any where I can post this bin file for you guys look at it ??

here's a pic

here's the bin file

Wayne

Isn't that function what is on the enter button in your bin file?

those function are on in the bin file ,but they are greyed out when the slingplayer launch.



Wayne

Is that picture you posted the default remote in slingplayer now? Or is that a remot that can be selected?

that picture is my Sling player remote with Y0631 bin & three grayed out buttons "MENU" "Page down" "-/--"