Page 1 of 2
Learns Work, Convert to Device Upgrade Does Not
Posted: Sun Feb 24, 2019 1:42 pm
by Jim-W
I'm using a Harmony 650 to learn several keys for an Apple TV 5th gen. and the learns work fine as does the Harmony.
When I "Convert to Device Upgrade" none of the upgrade buttons work but still the Harmony and the learns work fine.
I downloaded a couple of the Apple TV upgrades from the file section and none of those seem to work either.
I'm using RemoteMaster v2.07 build 4.
I tried an RCA RCRP058 black and a 67100 to no avail.
I've tried extenders v1.04, v1.03 and non-extended remotes.
Fresh batteries in all remotes.
I did notice the Convert to Device changes the Hex Cmd.
Uploaded a working file to the Diagnosis Area:
https://www.hifi-remote.com/forums/dload ... e_id=25525
Any help would be greatly appreciated.
Jim
Posted: Sun Feb 24, 2019 7:29 pm
by The Robman
The "Convert to Device Upgrade" feature is experimental at best, so it should only be used as a quick way to enter data for an upgrade, but you should still manually check the upgrade for correctness, especially for unusual protocols like Apple.
In this case, it incorrectly set the pair id to 0 rather than 1, it also didn't set the OBCs correctly.
This upgrade should work for you:
https://www.hifi-remote.com/forums/dload ... e_id=11767
Posted: Sun Feb 24, 2019 9:21 pm
by Jim-W
I tried that upgrade early on and it didn't work.
Where do I set the Pair ID?
Thanks
Jim
Posted: Mon Feb 25, 2019 8:39 am
by mdavej
Then try this one:
https://www.hifi-remote.com/forums/dload ... e_id=14185
Change the setup code to a lower number like 2001, then change the remote model to yours.
Posted: Mon Feb 25, 2019 12:07 pm
by Jim-W
I tried that one again just like you said, still doesn't work.
I've tried every Apple upgrade in the file section and nothing works but the Harmony and the learns work.
Example Learn Menu Button
Code: Select all
Menu Button Learn
Protocol = Apple
Device = 238
Sub Device = 135
OBC = 1
Hex Cmd = 3F
PairID=1 (How do I set PairID=1?)
Thanks
Posted: Mon Feb 25, 2019 12:21 pm
by mdavej
Both of those upgrades should work fine. Post the RMIR file where you attempted to load the upgrade(s) so we can take a look.
Pair ID is set on the main tab where the rest of the protocol parameter and setup code are.
Built in AUD 1644 or 1115 may also work.
Posted: Mon Feb 25, 2019 12:58 pm
by Jim-W
Posted: Mon Feb 25, 2019 2:25 pm
by Jim-W
Also Built in AUD 1644 or 1115 does not work.
And I don't see any Pair ID on the Setup tab.
Posted: Mon Feb 25, 2019 4:03 pm
by Jim-W
Also with IR Tool from a learned pronto I get:
Protocol: Gap-552-1683-32?
Device: 239.135
OBC: 1
EFC: 189
Posted: Thu Feb 28, 2019 10:17 am
by chuliu
I think you need to pair your remote with your apple tv.
My apple tv remote has pair id 149 or something, but harmony remote (when you download it with myharmony app, instead of learning it) has pair id 1. If you pair harmony remote with your apple tv, then apple tv remote won't work any more till you re-pair it, the same applies to jp1 remote.
Posted: Thu Feb 28, 2019 10:26 am
by Jim-W
chuliu wrote:I think you need to pair your remote with your apple tv.
My apple tv remote has pair id 149 or something, but harmony remote has pair id 1. If you pair harmony remote with your apple tv, then apple tv remote won't work any more till you re-pair it, the same applies to jp1 remote.
I ran across this by accident as the Harmony has pair and unpair buttons which worked.
Never heard of an IR remote needing to be paired.
Thanks!
Posted: Thu Feb 28, 2019 10:44 am
by chuliu
I think the idea is to avoid interference when one has more than one apple tv.
Therefore, each apple tv remote comes with different pairing id.
I set my jp1 remote with pairing id 1, same as that of harmony remote, so I can use harmony and my jp1 at the same time. The original remote can not work at the same time, though.
Posted: Fri Mar 01, 2019 2:57 am
by Jim-W
Where exactly do you set this pairing id 1?
chuliu wrote:I think the idea is to avoid interference when one has more than one apple tv.
Therefore, each apple tv remote comes with different pairing id.
I set my jp1 remote with pairing id 1, same as that of harmony remote, so I can use harmony and my jp1 at the same time. The original remote can not work at the same time, though.
Posted: Fri Mar 01, 2019 6:00 am
by pH7_jp1
On Feb 25, mdavej said:
Pair ID is set on the main tab where the rest of the protocol parameter and setup code are.
I opened your file and did the following:
- Devices (tab)
Choose the Apple (official) device
Edit
Setup (tab)
In the section "Protocol Parameters" the second item is "Pairing Dev:"
Posted: Fri Mar 01, 2019 7:11 am
by chuliu
https://photos.app.goo.gl/m9wCP94esok9rP4bA
I set the two values in the photo to 1.
You will need to pair it to your apple tv in the setting menu.