MENU  •   Set Up  •   Searching For Your Code  •   Blinking Back the Code
Redefining a Key  •   Clearing Out  •   Volume Lock
     Channel Lock  •   Channel Control Unlock

How to Program your NAVIGATOR remote


Set Up

After getting the proper codes from the list below

  1. PRESS the button for the device you want to program (TV,VCR,CABLE,etc.) then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER the 3 digit code for your brand.
  4. You should receive 2 quick flashes after entering your code.
  5. PRESS the POWER button to test the code. (On VCR,LD,and CD players use PLAY)

3 Digit Brand Codes

AMPLIFIERS
CD
RECEIVERS
TELEVISION
VCR
CABLE


menu

Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment, or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.
  1. PRESS the button for the device you want to program (TV,VCR,CABLE,etc.) then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE(TV,VCR,CABLE,etc.) button until your device turns off.(On VCR,LD,and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

menu

Blinking Back the Code:

  1. PRESS the device (TV,VCR,CABLE,etc.) button - RELEASE
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 0.
  4. PRESS 1, carefully COUNT the number of blinks. (1st digit)
  5. PRESS 2, carefully COUNT the number of blinks. (2nd digit)
  6. PRESS 3, carefully COUNT the number of blinks. (3rd digit)
If the remote DOES NOT blink it means the number is 0.
This is your 3-digit setup code.

menu

Redefining a Key

  1. PRESS the device (TV,VCR,CABLE,etc.) button - RELEASE
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 2.
  4. PRESS the DEVICE,(TV,VCR,CABLE,etc.),key you want moved
  5. PRESS the DEVICE key you want to replace.
Example: If you want the Audio key to be a TV key:
"SETUP" (2 blinks) 9 - 9 - 2, TV (you want to move TV)
Then AUDIO (you want to replace AUDIO).

menu

Clearing Out

A Device Key

  1. PRESS the device (TV,VCR,CABLE,etc.) button - RELEASE
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 2
  4. PRESS the device button twice. - Two blinks.
menu

Volume Lock

    1. Press and Hold in the SETUP key until the RED light flashes twice and then release the SETUP key
    2. Enter in 9-9-3
    3. Press and release the Device key from which you want volume controlled. (i.e. CABLE)


    menu

    Channel Control Lock

    1. Press and Hold in the SETUP key until the RED light flashes twice and then release the SETUP key
    2. Enter in 9-9-6 (Red light will blink twice after the 6)
    3. Press and release the Channel Up key


    menu

    Control Unlock

    1. Press and Hold in the SETUP key until the RED light flashes twice and then release the SETUP key
    2. Enter in 9-9-6 (Red light will blink twice after the 6)
    3. Press and Release the Channel Down key.





All Material Copyright ® Universal Electronics Inc.
Any questions about the products should be directed to cablehelp@ueic.com