MENU     Set Up     Searching For Your Code     Blinking Back the Code
Redefining a Key     Punch Through     Volume Default
Clearing Out    

How to Program your TWRC-2200 remote



Set Up

After getting the proper codes from the list below, use the following instructions to enter them into your remote.

  1. PRESS the button for the device you want to program (TV,VCR,CABLE,etc.) then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER the 3 digit code for your brand.
  4. You should receive 2 quick flashes after entering your code.
  5. PRESS the POWER button to test the code. (On VCR,LD,and CD players use PLAY)

3 Digit Brand Codes

CABLE
TELEVISION
VCR

menu

Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment, or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.
  1. PRESS the button for the device you want to program (TV,VCR,CABLE,etc.) then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE(TV,VCR,CABLE,etc.) button until your device turns off.(On VCR,LD,and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

menu

Blinking Back the Code:

  1. PRESS the device (TV,VCR,CABLE,etc.) button - RELEASE
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 0.
  4. PRESS 1, carefully COUNT the number of blinks. (1st digit)
  5. PRESS 2, carefully COUNT the number of blinks. (2nd digit)
  6. PRESS 3, carefully COUNT the number of blinks. (3rd digit)
If the remote DOES NOT blink it means the number is 0.
This is your 3-digit setup code.

menu

Redefining a Key

  1. PRESS the device (TV,VCR,CABLE,etc.) button - RELEASE
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 2.
  4. PRESS the DEVICE (TV,VCR,CABLE,etc.) key you want moved
  5. PRESS the DEVICE key you want to replace.
Example: If you want the Audio key to be a TV key:
"SETUP" (2 blinks) 9 - 9 - 2, TV (you want to move TV)
Then AUDIO (you want to replace AUDIO).

menu

Punch Through

This sets Volume to work for one device in all modes.
For example, the TV volume will work in the cable and VCR modes.
  1. PRESS the device (TV,VCR,CABLE,etc.) button - RELEASE
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 3.
  4. PRESS the device key from which you would like the volume to be controlled.
You will get two blinks on the remote.
NOTE: This only sets volume in the TV,VCR,CABLE, mode.


menu

Volume Default

Use this to get the original volume to work on each device.
  1. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  2. PRESS 9 - 9 - 3
  3. PRESS the VOLUME+ key, you will get two blinks.
Now The volume is set for all original devices.

menu

Clearing Out

A Device Key

  1. PRESS the device (TV,VCR,CABLE,etc.) button - RELEASE
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 2
  4. PRESS the device button twice. - Two blinks.


All Material Copyright Universal Electronics Inc.
Any questions about the products should be directed to cblhelp@ueic.com