The remote is preprogrammed at the factory to operate an RCA TV, VCR, and satellite receiver, a Motorola (General Instruments) cable converter, and Pioneer CD and DVD players, and audio devices. To control devices other than the default brands, perform the following steps and repeat them as needed for each device to be programmed; otherwise skip this section: NOTE: To control a TV/VCR Combo, see "Programming A TV/VCR Combo" see below.

1. Find the codes for the devices you want to program in Manufacturer’s Codes and write them down.

2. Turn on a device (e.g., VCR or DVD player) and, if necessary, load media (e.g., cassette or disc).
   NOTE: Please read steps 3 through 9 completely before proceeding. Write down the codes and device you wish to program before starting step 2.

3. On the remote, press and hold P until the display changes from the default device and time to [CODE SET].
   NOTE: If you wish to exit the programming mode at any time, press EXIT once. An [EXIT] message appears as the remote control returns to normal operation.
   NOTE:If an [INVALID] message appears, you have inadvertently pressed an incorrect key. Simply note your error and continue programming.

4. Press SELECT once to begin programming. The last-selected device and its current code (e.g., TV and 0051) appear.

5. Press a desired device key once (e.g., VCR). The desired device and its current code (e.g., VCR and 0035) appear.
   NOTE: Use the AUX key to program home automation devices, video accessories, audio services, and other audio/video devices.

6. Use the keypad to enter the first four-digit code for your device and press SELECT once.
   For example, to enter the first GE VCR code (on page 90), press 0 twice, 6 once, 0 once, and then SELECT once.
   If the code is entered correctly, the [SUCCESS] message appears.

7. Press EXIT to exit the programming mode. An [EXIT SETUP] message appears as the remote returns to normal operation.
   

8. To verify the code works, aim the remote at the desired device, press its device key once and then press POWER once. The device should turn off. If it does not respond, repeat steps 3 through 7, trying each code for your brand until you find one that works.
   NOTE: If the device does not have a POWER key, press (Play). Repeat steps 1 through 8 for each device you want to control.

Before proceeding, find the codes for the device you want to program in Setup Codes for TV/VCR Combos.

1. Turn on the TV/VCR Combo and insert a videocassette.

2. On the remote, press and hold P until the display changes from the default device and time to [CODE SET].
   NOTE: Default values for device, its code, and time are shown above. Your remote control settings may be different.
   NOTE: If you wish to exit the programming mode at any time, press EXIT once. An [EXIT] message appears as the remote control returns to normal operation.
   NOTE: If an [INVALID] message appears, you have inadvertently pressed an incorrect key. Simply note your error and continue programming.

3. Press SELECT once to begin programming. The last-selected device and its current code (e.g., TV and 0051) appear.

4. Press VCR once. [VCR] and its current code appear.

5. Use the keypad to enter the first four-digit code for your device and press SELECT once.
   For example, to enter the first Sony TV/VCR Combo, press 0 four times and then SELECT once. If the code is entered correctly, the [SUCCESS] message appears.

6. Press EXIT to exit the programming mode. An [EXIT SETUP] message appears as the remote returns to normal operation.

7. To verify the code works, aim the remote at the TV/VCR Combo, press VCR once and then press POWER once.
   NOTE: If the device does not have a POWER key, press (Play).
   The unit should turn off or start playing if you pressed (Play). If it does not respond, repeat steps 3 through 9, trying each code for your brand until you find one that works.