6-IN-1 Remote Control
(15-1934) Special Features Faxback Doc. # 62313
Searching For A Code
Before Setup
If you have tried all the codes from the list and your device still will
not respond to the 6-in-One (or if your brand is not listed), try
searching for your code.
For example, to find the code for a TV:
1. Turn on your TV, then press TV.
2. Hold down SETUP until TIMED SEQ appears.
3. Press MENU \/. CODE SETUP appears.
4. Press SELECT. DEV SET UP appears.
5. Press MENU \/. DEV SEARCH appears.
6. Press SELECT. TV and the last entered three digit code appear.
7. Press POWER. If your TV does not turn off, press MENU \/. The next
most recent code appears. Continue pressing POWER then MENU \/ until
your TV turns off. Then press SELECT to lock in the code and stop
programming.
Repeat these steps, using the appropriate device control button for each
device you need to search.
Note: If you are searching for a VCR, laser disc player, or DVD player
code, you might need to use PL (Play) instead of POWER.
After Setup
After you have set up your devices, you might need to find out which code
is operating your TV:
1. Press TV.
2. Hold down SETUP until TIMED SEQ appears.
3. Press MENU \/. CODE SETUP appears.
4. Press SELECT. DEV SET UP appears.
5. Press MENU \/ twice. DEV NUMBER appears.
6. Press SELECT. TV and the code for that device appear.
Note: To view the three-digit code for another device, press the key
for that device.
7. Write down the three-digit code then press ESC to stop programming.
Using The Sleep Function
To use the sleep timer built into your TV, cable converter, satellite
system, or audio device, press SLEEP (SHIFT then MUTE). Most sleep timers
advance in increments of 10 or 15 minutes. For specific instructions on
setting your device's sleep timer, refer to the device's owner's manual.
If your device does not have a sleep timer, follow these steps to enable
Sleep Lock. Then you can use the 6-in-One's built-in sleep timer on all
devices.
1. Hold down SETUP until TIMED SEQ appears.
2. Press MENU \/ twice. CONFIGURE appears.
3. Press SELECT. TIME SETUP appears.
4. Press MENU \/ twice. SLEEP LOCK appears.
5. Press SELECT. DISABLE appears.
6. Press MENU \/. ENABLE appears.
7. Press SELECT to stop programming.
Whenever you press SLEEP (SHIFT then MUTE), SLEEP 15 appears. To add time
to the sleep timer, press MENU \/. Each press of MENU \/ adds 15 minutes
to the sleep timer, up to a total of 60 minutes. When the desired sleep
time appears, press SELECT. SLEEP appears.
Note: When Sleep Lock is enabled, the 6-in-One will only activate its own
Sleep Timer. To use another device's sleep timer, you must repeat
these steps, press MENU /\ to disable Sleep Lock in Step 6.
Reassigning Device Keys
You can use the 6-in-One to operate a second TV or VCR, or any combination
of up to six devices. To do this, you must first assign one of the device
keys (TV, VCR, CD, CBL, SAT or AUX) to operate your second device.
For example, to re-assign CBL to operate a second TV.
1. Hold down SETUP until TIMED SEQ appears.
2. Press MENU \/ twice. CONFIGURE appears.
3. Press SELECT. THEATR SEL appears.
4. Press MENU \/ three times. MODE MAP appears.
5. Press SELECT. SOURCE appears.
6. Press TV. COPY TO appears.
7. Press CBL. TV2 appears.
8. Program the reassigned device key (CBL) with the code for the second
TV. (See "To Operate Your TV" in Faxback Doc. # 62306.)
Repeat these steps for each key you want to reassign.
Volume Lock
The 6-in-One lets you choose which device controls the sound volume. When
you first set up the 6-in-One, each device with a volume control operates
its own volume. You can change this so that one device controls the volume
no matter which device the 6-in-One is operating.
For example, to set-up the 6-in-One to always control the volume through
your receiver:
1. Hold down SETUP until TIMED SEQ appears.
2. Press MENU \/ twice. CONFIGURE appears.
3. Press SELECT. THEATR SEL appears.
4. Press MENU \/ twice. VOL LOCK appears.
5. Press SELECT. UNLOCK appears.
6. Press MENU \/. LOCK appears.
7. Press SELECT then the key for the device that you want to control the
sound volume (TV, VCR, CD, CBL, SAT, or AUX), then press SELECT again.
For example, to control the volume through your receiver, press AUX
then SELECT. When you press the volume keys on your 6-in-One, your
receiver controls the volume.
8. Press ESC to exit.
Note: You might need to use the MENU or VOL keys to control volume,
depending on which device you selected to control volume.
Resetting Volume Lock
To restore volume control to each individual device:
1. Hold down SETUP until TIMED SEQ appears.
2. Press MENU \/ twice. CONFIGURE appears.
3. Press SELECT. THEATR SEL appears.
4. Press MENU \/ twice. VOL LOCK appears.
5. Press SELECT. LOCK appears.
6. Press MENU \/. UNLOCK appears.
7. Press SELECT. Each device now controls its own volume when you use
the volume keys on your 6-in-One.
Key Mover
Key Mover lets you map features from one device mode to another. For
example, if your VCR has no volume control, you can map the remote's
volume keys to control the TV's volume in VCR mode. To map features from
one device mode to another:
1. Hold down SETUP until TIMED SEQ appears.
2. Press MENU \/ twice. CONFIGURE appears.
3. Press SELECT. THEATR SEL appears.
4. Press MENU /\ three times. KEY MOVER appears.
5. Press SELECT. FROM appears.
6. Press the key for the device (TV, VCR, CD, CBL, SAT or AUX) where the
feature you want to move is currently located, then the key for the
feature you want to move. Press the key for the device where you want
to move the feature, then press the feature key again.
For example, to move the TV's volume to VCR, press TV then VOL+. TO
appears. Press VCR then VOL+. When you press VOL+ in VCR mode, your
6-in-One's volume keys operate the TV's volume.
Resetting Mapped Functions
1. Hold down SETUP. TIMED SEQ appears.
2. Press MENU \/ twice. CONFIGURE appears.
3. Press SELECT. THEATR SEL appears.
4. Press MENU /\ three times. KEY MOVER appears.
5. Press SELECT. FROM appears.
6. Press the key for the device (TV, VCR, CD, CBL, SAT or AUX) where you
want the feature to be located. Then the key for the feature you want
to reset. Press the device key again, then press the feature key again
For example, to reset the VCR's VOL keys, press VCR, then VOL+. TO
appears. Press VCR then VOL+. The 6-in-One's volume keys no longer
control the TV's volume in the VCR mode.
Using the Macro Keys
The 6-in-One has two macro keys, A and B, that let you play back a series
of up to 15 keystrokes at any time with the press of a single key, in any
mode.
Note: If you make a mistake, press ESC and start over at Step 1.
For example, to set up a sequence that turns on your TV, VCR, and
Satellite system so you can record a program:
1. Hold down SETUP. TIMED SEQ appears.
2. Press MENU twice. CONFIGURE appears.
3. Press SELECT. THEATER SEL appears.
4. Press MENU four times. KEY MACRO appears.
5. Entering the sequence of up to 15 keystrokes that you want to be
entered automatically when you press the macro key you selected, then
press ESC.
For example:
TV POWER 0 4 TV VCR SAT POWER
Whenever you press the macro key you selected in Step 6, the TV turns
On, tunes to channel 4, and changes its input to VIDEO 1, then the
satellite turns on.
Note: When setting up a sequence, you must include any keystrokes that
you would enter during regular usage, such as pressing ENTER
after a channel number when changing channels if your TV
requires it.
Repeat these steps to set up another sequence on the other macro key.
Setting Up Timed Sequences
The 6-in-One lets you set up a sequence of keystrokes that can be played
back at a time you specify, up to seven days in advance. You can use this
feature to set up any series of keystrokes that you would like to play
back at a later time.
Note: If you make a mistake, press ESC and start over at Step 1.
For example, to set your VCR to record a program from your satellite
system:
1. Hold down SETUP until TIMED SEQ appears.
2. Repeatedly press SELECT until START and the time appear, with the
first digit blinking. Enter the time in 12-hour format. AM/PM
flashes.
3. If necessary, press MENU \/ to toggle between AM and PM, then press
SELECT. ONCE appears.
4. Press MENU /\ or MENU \/ to toggle between ONCE, DAILY, and WEEKLY.
When the desired frequency appears, press SELECT. The day of the week
display appears.
5. Use MENU \/ and /\ to toggle through the days of the week until the
day when you want the sequence to start running appears.
6. Press SELECT. ENTER SEQ appears.
7. Enter the sequence of keystrokes you want to set up then press ESC.
For example, to set up a sequence that turns on the satellite, tune to
channel 275, turns on the VCR and starts recording, enter:
SAT POWER SAT 2 7 5 VCR POWER VCR RECORD
When your sequence is set up, the clock icon appears.
Deleting a Timed Sequence
1. Hold down SETUP until TIMED SEQ appears.
2. Press SELECT. ADD MACRO appears.
3. Press MENU /\ or MENU \/. DEL MARCO appears.
4. Press SELECT. DEL (the day and time) appears.
5. If necessary, use MENU /\ or MENU \/ to scroll through the saved timed
sequences. When you see the one you want to delete, press SELECT.
DELETED appears. If there are more timed sequences, the next one
appears.
Setting Up The Home Theater Mode Key
The 6-in-One lets you operate all of the most commonly used home theater
functions in one mode. When setting up the Home Theater mode, you choose
which devices will control volume, channel changing, playback, picture-in
picture, and menu functions.
1. Press HOME THEATER.
2. Hold down SETUP until TIMED SEQ appears.
3. Press MENU \/ twice. CONFIGURE appears.
4. Press SELECT twice. AUDIO appears.
5. Press SELECT then the appropriate device key (TV, CBL, SAT, VCR, or
AUX) to Select the device that you want to control audio features in
Home Theater mode, then press SELECT. CHANNEL appears.
6. Press SELECT, then the appropriate device key to select the device
that you want to change channels in Home Theater mode. Then press
SELECT again. PLAYBACK appears.
7. Press SELECT, then CD or VCR to select the device that you want to
control the transport keys (PLAY, REW, FF, PAUSE, STOP and REC) in
Home Theater mode. Then press SELECT again. PIP (Picture-in-Picture)
appears.
8. Press SELECT then TV, CBL, or VCR to select the device that you want
to control Picture-in-Picture features in Home Theater mode. Then
press SELECT again. MENU appears.
9. Press SELECT then the appropriate key to select the device you want to
control the menu features in Home Theater mode. Then press SELECT
again to stop programming.
Setting Up a Power Key Marco
After you set up the HOME THEATER key, you can create a macro sequence
that lets you use POWER to turn on all of your Home Theater devices.
1. Press HOME THEATER, then hold down SETUP until TIMED SEQ appears.
2. Press MENU- twice. CONFIGURE appears.
3. Press SELECT. THEATER SEL appears.
4. Repeatedly press MENU- until KEY MACRO appears.
5. Press SELECT. SEL MACKEY appears.
6. Press POWER then enter the keys which control all of your Home Theater
devices, pressing POWER after device key.
For example, POWER AUX POWER TV POWER VCR POWER and so on.
Note: You cannot use A or B in your Home Theater Power key macro.
7. Press ESC to stop programming. To activate the Home Theater macro,
press HOME THEATER so THEATER appears, then press POWER.
Clear All
Use the Clear All feature to reset all advanced functions of the 6-in-One.
Clear all erases macro sequences, timed macro sequences, Volume Lock and
Key Mover from the 6-in-One's memory. It does not erase setup codes.
To clear the memory using the Clear All features:
1. Hold down SETUP. TIMED SEQ appears.
2. Press MENU \/ twice. CONFIGURE appears.
3. Press SELECT. THEATER SEL appears.
4. Press MENU /\. CLEAR ALL appears.
5. Press SELECT. CLR ALL appears.
6. Press SELECT again. CONFIRM appears.
7. Press SELECT once more. Your 6-in-0ne is reset.
(LB EB 10/3/00)