6-IN-1 Remote Control
(15-1934) Preparation Faxback Doc. # 62305
Installing Batteries
Your 6-in-One requires four AAA alkaline batteries (not supplied),
available at your local RadioShack store.
CAUTIONS: Use only fresh batteries of the required size and recommended
type.
Do not mix old and new batteries, different types of batteries
(standard, alkaline, or rechargeable) or rechargeable batteries
of different capacities.
To install the batteries:
1. Press down on the battery compartment cover and slide it off.
2. Place the batteries in the compartment, matching the polarity marks
(+ and -) inside.
3. Replace the cover.
If the batteries are installed correctly and the red indicator does not
light when you press POWER, replace the batteries.
CAUTIONS: Dispose of old batteries promptly and properly. Do not burn or
bury them.
Always remove old or weak batteries. Batteries can leak
chemicals that can destroy electronic parts.
Notes: After you install batteries, the remote performs a test of the
display for 10 seconds or until you press a key.
To extend battery life, the display turns off after 10 seconds of
keypad inactivity and turns on again when you press any key.
Device codes you have programmed into the 6-in-One remain stored in
memory while you replace the batteries. However, you must reset the
clock.
Setting The Clock
Follow these steps to set the clock on the 6-in-One's display:
1. Hold down SETUP until TIMED SEQ. appears.
2. Press MENU \/ twice. CONFIGURE appears.
3. Press SELECT. THEATR SEL appears.
4. Press MENU \/ again.
5. Press SELECT. TIME appears and the first digit in the time flashes.
Enter the time in 12-hour format. AM/PM flashes.
6. If necessary, press MENU \/ to toggle between AM and PM, then press
SELECT. The day of the week display appears.
7. Use MENU /\ and \/ to toggle through the days of the week until the
current day appears, then press SELECT. The currently selected device
and the correct time appear.
Quick Setup
The steps in this section tell you how to quickly set up the 6-in-One to
operate all of your devices.
To set up devices individually, or add a device after you have set up the
6-in-One, see the appropriate section under "Setting Up the Remote" in
Faxback Doc. 62306.
Note: For the best operation, you should be within 15 feel of the device
you want to control.
Follow these steps for quick setup.
1. Turn on all of the devices you are setting up.
2. Press TV.
3. Hold down SETUP until TIMED SEQ appears.
4. Press MENU \/. CODE SETUP appears.
5. Press SELECT. DEV SET UP appears.
6. Press SELECT again. TV appears.
7. Enter the first three-digit TV code listed for your TV's brand in "Set
Codes for TV's" in Faxback Doc. # 62306, then press SELECT.
8. Point the remote at your TV and press POWER. Your TV should turn off.
If it does not, enter the next code from the list and press SELECT
then POWER again. When your TV turns off, press VCR. VCR appears.
9. Enter the first three-digit VCR code listed for your VCR's brand in
"Setup Codes for VCR's" or "Setup Codes for TV/VCR Combos" in Faxback
Doc. # 62307, then press SELECT.
10. Point the remote at your VCR and press POWER. Your VCR should turn
off. If it does not, enter the next code from the list and press
SELECT then POWER again. When your VCR turns off, press CBL. CABLE
appears.
11. Continue setting up devices by pressing the appropriate device key,
entering your device's code and pressing SELECT. Refer to the code
list for the type of device you want to set up:
Setup Codes for: Faxback Doc. # :
Amplifiers 62311
Cable Converters 62308
Cassette Players 62312
CD Player 62310
DAT 62312
Satellite Receivers 62309
DVD Player 62312
Home Automation 62312
Laser Disc Players 62312
Miscellaneous Audio 62312
Phonographs 62312
Receivers/Tuners 62311
12. Once the 6-in-One is operating all of your devices, press ESC to stop
programming.
(LB EB 10/3/00)