6-in-One Smart Audio/Video Remote Control
(15-1994) Operation Faxback Doc. # 58320
1. Press the device key for the device you want to control.
2. Point the remote control toward the device you want to control, then
press the desired command keys.
3. Repeat Steps 1 and 2 for all other devices you want to operate.
Note: The command keys on the remote control work the same as the
keys on the original remote control; however, the labeling
might differ slightly.
4. To turn off the last device you selected, press POWER. To turn off
other devices, press the device key for the device you want to turn
off, then press POWER.
Using The Light
The backlight lets you see the keys on your 6-in-One in the dark. Press
(light symbol) to turn on the light. The keypad lights for about 5
seconds. Then, every time you press a key, the 6-in-One lights up and
stays lit for about 5 seconds. To turn off the light, press (light
symbol) again.
Using Punch-Through
Punch-Through lets you alternately control two different devices without
pressing the device keys for each one.
For example, a TV is often the only device that uses the volume keys. With
the 6-in-One programmed to punch-through to the TV, you can control the
TV's volume while the 6-in-One is in any device mode.
1. Hold down P until the red light blinks twice.
2. Press 9 9 3.
3. Press TV. When you press VCR (or another device key) and use your
volume keys, the 6-in-One controls the volume through the TV instead
of the VCR (or the other device).
Turning Punch-Through Off
1. Hold down P until the red light blinks twice.
2. Press 9 9 3.
3. Press VOL +. The 6-in-One controls the volume through the currently
selected device. (For example, when you press VCR, the 6-in-One
controls the volume through the VCR; when you press CBL, the 6-in-One
controls the volume through the cable converter.)
Note: The 6-in-One A/V cannot control volume through a device which
does not have a volume control.
Using The Smart Keys
Your RadioShack 6-in-One Smart A/V Remote can "learn" up to 24 features
from your original remote control using Smart Technology. Your remote is
equipped with four Smart Keys (1s, 2s, 3s and 4s) that you can program to
perform special functions from your original remotes.
For example, if your original remote has a button labeled CLOCK, the 6-in
one does not come with this feature preprogrammed. Follow these steps to
program one of the Smart Keys to perform the function of the CLOCK button:
1. Place your original remote control nose-to-nose with the RadioShack
Smart Light-Up Remote Control.
2. Hold down P until the red light blinks twice, then press 975. The red
light blinks twice again.
3. Press a device key (TV, VCR, CBL, CD, AUX 1, or AUX 2) to select where
the function will reside.
Note: You can use each Smart Key for one feature in each of the four
modes. For example, 1s can be programmed for CLOCK in TV mode
and TRACKING in VCR mode.
4. Press one of the four Smart Keys (1s, 2s, 3s, or 4s). The red light
blinks rapidly.
5. Hold down the key on your original remote that you want the 6-in-One
to learn until the red light blinks twice.
6. Hold down P until the red light blinks twice.
7. Press the Smart Key you pressed in Step 4. The 6-in-One performs the
function it learned from your original remote control.
8. Repeat Steps 1-7 to program more functions onto the Smart Keys.
Clearing Smart Keys
You can clear a function that you previously programmed to a Smart Key to
make room for a new function. Follow these steps to clear a Smart Key:
1. Hold down P until the red light blinks twice.
2. Press 976. The red light blinks twice.
3. Press the Smart Key you want to clear twice. The red light blinks
twice and the key is cleared.
Using Favorite Channel Scan
You can program your 6-in-One Remote to scan through 10 of your favorite
channels in either TV, VCR, or Cable modes.
Note: You can only maintain a favorite channel list for one device at a
time. You cannot set up a favorite channel list for another device
until you clear the existing list.
1. Press the device key for the device you want to scan (TV, VCR, or
CBL). The red light blinks.
2. Hold down P until the red light blinks twice, then press 9 9 6.
3. Enter the first channel number you want to include in your favorite
channel list, then press P.
Notes: Precede a single-digit number with a 0. For example, 0 1, 02,
and so on.
If you enter a three-digit number, you do not need to press P
after entering the number.
If you use an ENTER key to directly access channels on your
original remote, press ENTER after you enter the last digit of
a channel.
4. Repeat Step 3 for up to 9 other channels you want to include in your
list, then hold down P until the red light blinks twice.
5. To scan through your favorite channel list, press the appropriate
device key, point the remote at your device, then press SCAN. The
remote control repeatedly scans through the favorite channel list,
stopping on each channel for about 3 seconds.
6. Press any key when you see a channel you want to watch. Scanning
stops.
Note: If you do not program a favorite channel list, SCAN acts as a
"channel surf" key. Each time you press SCAN, the 6-in-One
repeatedly performs cycles through the channels, stopping on each
for about 3 seconds.
Clearing Favorite Channel Scan
To change your favorite channel list, you must first clear the existing
list. Hold down P until the red light blinks twice. Press 9 9 6, then
hold down P until the red light blinks twice. The list is cleared.
Using The Sleep Function
To use the sleep timer built into your TV, cable converter, satellite
system, or audio device, press SLEEP. Most sleep timers advance in
increments of 10 or 15 minutes. For specific instructions on setting your
device's sleep timer, refer to the device's owner's manual.
If your TV, cable or satellite system does not have a sleep timer, the 6
in-One has a built-in sleep timer that can perform the function.
1. Press the appropriate device key.
2. Press SLEEP to set the 6-in-One's sleep timer for 15 minutes. The red
light blinks once.
3. Each additional press of SLEEP adds 15 minutes to the sleep timer, up
to 60 minutes. The red light blinks twice when the sleep timer is set
for 30 minutes, 3 times for 45 minutes, or 4 times for 60 minutes.
Note: The 6-in-One's sleep timer starts 10 seconds after the last
time you press SLEEP. Once you activate the sleep timer, you
must keep the remote control aimed directly at the component
for this feature to operate.
(BR EB 1/20/00)