4-in-One Smart Light-Up Remote Control
(15-1993)                 Operation                  Faxback Doc. # 58278

1.  Press the device key for the device you want to control.

2.  Point the remote control toward the device you want to control, then
    press the desired command keys. 

3.  Repeat Steps 1 and 2 for all other devices you want to operate.

    Note:  The command keys on the remote control work the same as the 
           keys on the original remote control; however, the labeling 
           might differ slightly. 

4.  To turn off the last device you selected, press POWER.  To turn off
    other devices, press the device key for the device you want to turn
    off, then press POWER.

Using The Smart Technology

Your RadioShack 4-in-One Smart Light-Up Remote Control can "learn" up to 
16 features from your original remote control using Smart Technology.  Its 
four smart keys (1s, 2s, 3s, and 4s)can be programmed to perform functions 
from your original remote that are not already available on your 4-in One 
Smart Light-Up.

Example:  Your original remote may have a button called MENU.
          Unfortunately, the 4-in-one Smart Light-Up remote does not 
          include this feature.  But with Smart Technology, you can 
          program one of the four smart keys to perform the functions of 
          your original remote's MENU key.

1.  Place your original remote control nose-to-nose with the RadioShack 
    Smart Light-Up Remote Control.

2.  Hold down P until the red light blinks twice, then press 975.  The red 
    light blinks twice again.

3.  Press the device key (TV, VCR, CBL, or AUX) for the mode where you 
    want the function to reside.

    Note:  You can program each smart key for a different function in each
           of the four modes.  For example, 1s might serve as a MENU key 
           in TV mode and a TRACKING key in VCR mode.

4.  Press one of the smart keys.  The red light blinks rapidly


5.  Hold down the key that you want to copy on your original remote until
    the red light on the 4-in-One Smart Light-Up blinks twice.

6.  Hold down P until the red light blinks twice.

7.  Press the smart key you programmed.  The key should control the same
    function as the key that you copied from your original remote.

8.  Repeat Steps 1-7 to program other smart keys.

Deleting Learned Functions From Smart Keys

You can delete learned functions from the smart keys (1s, 2s, 3s, and 4s) 
to make room for other functions.

1.  Hold down P until the red light blinks twice.

2.  Press 976.  The red light blinks twice.

3.  Press the device key (TV, VCR, CBL, or AUX) where the learned function
    resides.

4.  Press the smart key you programmed with the function twice to delete
    the learned function.  The red light blinks twice.

Converting Device Keys

You can use the 4-in-One Smart Light-Up to operate a second TV or VCR (or 
other components) for a total of up to four devices.  To do this, you must 
first convert an unused device key (TV, VCR, CBL, AUX) to operate each 
additional device.  For example, to convert AUX to operate a second TV:

1.  Hold down P until the red light blinks twice.

2.  Press 9 9 2.  The red light blinks twice.

3.  Press TV.

4.  Press AUX.  The red light blinks twice.

5.  Program the converted device key (AUX) with the code for the second 
    TV.  (See "Setting Up Your Remote Control" in Faxback Doc. # 58277.)

Repeat these steps for each key you want to convert.  To convert a key 
back to its original function, repeat Steps 1 - 2, then press AUX twice.

Punch-through

The punch-through feature lets you alternately control two different 
devices without pressing the device keys for each one. 

A TV is often the only device that uses the volume keys.  Punch-through 
allows you to control the TV's volume while the 4-in-One is in any device 
mode.  With punch-through on, if you press VCR and use your volume keys, 
the 4-in-One will control the TV's volume instead of the VCR's.

Turning Punch-Through Off/On

If your cable converter or VCR has volume control, you might want to turn 
off punch-through so you can use the cable converter's or VCR's volume 
instead of the TVs.  To turn off punch-through:

1.  Hold P until the red light blinks twice. 

2.  Press 9 9 3, then VOL +.  The red light blinks four times.

3.  When you want to control the volume through your cable converter, 
    press CBL before using the volume control.

To turn punch-through back on:

1.  Hold down P until the red light blinks twice.

2.  Press 9 9 3, then the key for the device you want to control all
    volume (TV, for example).  The red light blinks twice and the device
    you chose controls volume whenever you press a volume key on the 4-in
    One.

Favorite Channel Scan

You can use your remote control to scan through up to 10 of your favorite 
channels on your TV, VCR, or cable box.

Note: You can scan channels only for one device (TV, VCR, cable converter)
      at a time.  You cannot set up a favorite channel list for another 
      device until you clear the existing list.

1.  Press the device key for the device with the channels you want to scan 
    (TV, VCR, or CBL).  The red light blinks.

2.  Hold down P until the red light blinks twice, then press 9 9 6.

3.  Enter the channel number of the first channel you want to include in
    your favorite channel list.  Then press P.

    Notes:  Precede a single-digit number with a 0 (for example, 01, 02, 
            and so on).

            If you enter a three-digit number, you do not need to press P 
            after entering the number.

            If your TV requires an ENTER key when entering a channel 
            number, press ENTER after you enter the channel number.

4.  Repeat Step 3 for other channels (up to 10) you want to include in
    your list.  Then hold down P until the red light blinks twice.

5.  To scan through the favorite channel list, press the device key for
    the device you want to tune (TV, VCR, or CBL), then press SCAN.  The
    remote control repeatedly scans through the favorite channel list,
    stopping on each channel for about 3 seconds.

6.  Press any key other than SCAN when you see a channel you want to
    watch.  Scanning stops.

Clearing Favorite Channel scan

You must clear the channels in your favorite channel scan list if you want 
to change them.

1.  Hold down P until the red light blinks twice.

2.  Press 9 9 6, then hold down P until the red light blinks twice.

Using the Light

The back light lets you see the keys on your 4-in-One Smart Light-Up in 
the dark.  Press (light bulb symbol) to turn on the feature.  Every time 
you press a key, the 4-in-One Smart Light-Up lights and stays lit for a 
few seconds.  To turn off the light, press (light bulb symbol) again.

(BR EB 1/12/00)