4-in-One Smart Light-Up Remote Control
(15-1993)                 Preparation                Faxback Doc. # 58277

Installing Batteries

Your remote control requires four AAA batteries (not supplied) for power.  
For the best performance and longest life, we recommend RadioShack 
alkaline batteries.

CAUTIONS:  Use only fresh batteries of the required size and recommended 
           type.

           Do not mix old and new batteries or different types of 
           batteries.

           Do not press any of the remote control's keys while installing 
           batteries.

Note:  You do not need to reprogram your remote control after removing the 
       batteries, because no stored information is lost during battery 
       replacement.

1.  Press the battery compartment cover's tab and lift off the cover.

2.  Place the batteries in the compartment as indicated by the polarity
    symbols (+ and -) marked inside.

3.  Replace the cover.

When the remote control's range decreases or it stops operating, replace 
the batteries.

CAUTION:  Always remove old or weak batteries.  Batteries can leak 
          chemicals that can destroy electronic parts. 

WARNING:  Dispose of old batteries promptly and properly.  Do not burn or 
          bury them.

Note:  Do not place objects on top of the remote control after you have 
       installed the batteries. This can press keys for an extended period
       of time and reduce the battery life.

Device Types

You can use the remote control's device keys to control the following 
types of devices:

 TV - TVs.

VCR - VCRs and TV/VCR combinations.

CBL - Cable converters, satellite systems.

AUX - CD Players, Home Automation.

Setting Up Your Remote Control

1.  Refer to "Manufacturer Codes" in Faxback Doc. # 58280 and write down
    the codes for your brand of device on the 4-in-One's label.

    Note:  Some manufacturers have several codes listed.  Try each until 
           you find the right one.  See "If You Have Problems" in Faxback
           Doc. # 58279 if you cannot find the correct code.

2.  Press the device key for the type of remote you are replacing (TV,
    VCR, CBL, or AUX).  The red light blinks.

3.  Hold down P until the red light blinks twice, then enter the 4-digit
    manufacturer's code.

    For example, to replace a Panasonic TV's remote control
    (manufacturer's code 0051), press TV, hold down P until the red light 
    blinks twice, then press 0051.

    When the red light blinks twice, the remote control has accepted the 
    code.

    Note:  If the code you entered is invalid, the red light blinks.

4.  Point the remote control at your device and press POWER.  Your device 
    should turn off (or on, if it was off).

    If the remote does not operate your device, try the other codes you 
    listed in "Manufacturer Codes" in Faxback Doc. # 58280, for your brand
    of TV, VCR, cable converter, or CD player.

5.  Repeat Steps 2-4 for additional devices.

To operate your TV/VCR combination

1.  Locate the codes for your TV/VCR combination in "TV/VCR Combinations"
    in Faxback Doc. # 58280 and write them on the 4-in-One's label.

2.  Press VCR.  The red light blinks.

3.  Hold down P until the red light blinks twice, then enter the 4-digit
    manufacturer's code. 

    When the red light blinks twice again, the remote control has accepted
    the code. 

    Note:  If the code you entered is invalid, the red light blinks.

4.  Point the remote control at your TV/VCR combination and press POWER.
    Your device should turn off (or on, if it was off).

    If the remote does not operate your device, try the other codes you 
    wrote down in Step 1.
 
    Note:  Some TV/VCR combinations require a second code to control 
           volume.  If you cannot control volume, use the TV code listed
           in "TV/VCR Combinations" in Faxback Doc. # 58280.

(BR EB 1/12/00)