3-IN-1 Pocket Remote Control
(15-1990)                 Preparation                Faxback Doc. # 56064

Installing Batteries

Your remote control requires two AAA batteries (not supplied) for power.  
For the best performance and longest life, we recommend RadioShack 
alkaline batteries.

CAUTIONS:  Use only fresh batteries of the required size and recommended
           type.

           Do not mix old and new batteries or different types of
           batteries.

           Do not press any of the remote control's keys while installing
           batteries.

Note:  The remote control's built-in memory backup saves any programmed
       codes for about 10 minutes after the batteries have been removed.
       We recommend you have fresh batteries ready to install as soon as
       you remove the old ones.

1.  Press the battery compartment cover's tab and lift off the cover.

2.  Place the batteries in the compartment as indicated by the polarity
    symbols (+ and -) marked inside.

3.  Replace the cover.

When the remote control's range decreases or it stops operating properly, 
replace the batteries.

CAUTION:  Always remove old or weak batteries.  Batteries can leak
          chemicals that can destroy electronic parts.

WARNING:  Dispose of old batteries promptly and properly.  Do not burn or
          bury them.

Note:  Do not place objects on top of the remote control after you have
       installed the batteries. This can press keys for an extended period
       of time and reduce battery life.

Device Types

You can use the remote control's device keys to control the following 
general types of devices:

   TV - TVs

  VCR - VCRs and TV/VCR combinations

  CBL - Cable converters

Setting Up Your Remote Control

1.  Refer to "Manufacturers' Codes" in Faxback Doc. # 56066 and write down
    the codes for your brand of device on the 3-in-One's label.

    Note:  Some manufacturers have several codes listed.  Try each until
           you find the right one. See "If You Have Problems" in Faxback
           Doc. # 56067 if you cannot find the correct code.

2.  Press the device key for the type of remote you are replacing (TV,
    VCR, or CBL).  The red light blinks.

3.  Hold down P until the red light blinks twice, then enter the 4-digit
    code you wrote down in Step 1 using these keys:

      Press    To Enter This Number

      VOL +           1

      VOL -           2

      CH  +           3

      CH  -           4

      MUTE            5

    For example, to replace a TV's remote control (Manufacturer's Code
    1432), press TV, hold down P until the red light blinks twice, then
    press VOL +, CH -, CH +, and VOL -.

    When the red light blinks twice, the remote control has accepted the
    code.

    Note:  If the code you entered is invalid, the red light blinks.

4.  Point the remote control at your device and press POWER.  Your device
    should turn OFF (or ON, if it was off).

    If the remote does not operate your device, try the other codes listed
    in "Manufacturers' Codes" in Faxback Doc. # 56066 for your brand of
    TV, VCR, TV/VCR combination, or cable converter.

5.  Repeat Steps 2 - 4 for additional devices.

To Operate Your TV/VCR Combination

1.  Locate the codes for your TV/VCR combination in "TV/VCR Combinations"
    in Faxback Doc. # 56066 and write down the codes for your brand of
    device on the 3-in-One's label.

2.  Press VCR.  The red light blinks.

3.  Hold down P until the red light blinks twice, then enter the 4-digit
    code you wrote down in Step 1 using these keys:

      Press       To Enter This Number

      VOL +             1

      VOL -             2

      CH  +             3

      CH  -             4

      MUTE              5

    When the red light blinks twice, the remote control has accepted the
    code.

    Note:  If the code you entered in invalid, the red light blinks.

4.  Point the remote control at your TV/VCR combination and press POWER.
    Your device should turn OFF (or ON, if it was off).

    If the remote does not operate your device, try the other codes listed
    in "TV/VCR Combinations" in Faxback Doc. # 56066 for your TV/VCR
    combination.

    Note:  Some TV/VCR combinations require a second code to control
           volume.  If you cannot get the volume to work, use the TV code
           listed in "TV/VCR Combinations."  If no TV code is listed,
           follow the instructions in "Punch Through" in Faxback Doc. #
           56065 to control volume.

(EB 7/26/99)
(EB - Rev. 1/11/00)