MENU     Set Up     Searching For Yor Code     Blinking Back the Code
Redefining a Key     Punch Through     Volume Default     Clearing Out
Key Mover     Macro-Sequence     How To Learn Functions
Programming your One For All® remote

How to Program your One For All® Pro Producer 7 remote

(Model Pro Producer 7 URC-7070 )


Set Up

After getting the proper codes from your manual or Customer Service, use the following instructions to enter them into your remote.

  1. PRESS the button for the device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  3. ENTER the 3 digit code for your brand.
  4. You should receive 2 quick flashes after entering your code.
  5. PRESS the POWER button to test the code. (On VCR,LD,and CD players use PLAY)

menu

Searching For Yor Code

If you have tried all of the set-up codes for your brand of eqipment, or your brand is not listed, and you are still not able to get the unit to respond, try the following proceedure to search for your code.
  1. PRESS the button for the device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE(TV,VCR,CABLE,etc.) button until your device turns off.(On VCR,LD,and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the MAGIC button and RELEASE it to lock in the code for your device.

menu

Blinking Back the Code:

  1. PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 0.
  4. PRESS 1, carefully COUNT the number of blinks. (1st digit)
  5. PRESS 2, carefully COUNT the number of blinks. (2nd digit)
  6. PRESS 3, carefully COUNT the number of blinks. (3rd digit)
If the remote DOES NOT blink it means the number is 0.
This is your 3-digit setup code.

menu

Redefining a Key

  1. PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 2.
  4. PRESS the DEVICE,(TV,VCR,CABLE,etc.),key you want moved
  5. PRESS the DEVICE key you want to replace.
Example: If you want the Aux key to be a TV key:
"MAGIC" (2 blinks) 9 - 9 - 2, TV (you want to move TV)
Then AUX (you want to replace AUX).

menu

Punch Through

This sets Volume to work for one device in all modes.
For example, the TV volume will work in the cable and VCR modes.
  1. PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 3.
  4. PRESS the device key you would like the volume to come from.
You will get two blinks on the remote.
NOTE: This only sets volume in the TV,VCR,CABLE, or SAT mode.
If you want to set the volume for a device to work just one or two other devices- refer to the instructions under "KEYMOVER-From one button to another"

menu

Volume Default

Use this to get the original volume to work on each device.
  1. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  2. PRESS 9 - 9 - 3
  3. PRESS the VOLUME+ key, you will get two blinks.
Now The volume is set for all original devices.

menu

Clearing Out

A Device Key

  1. PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 2
  4. PRESS the device button twice. - Two blinks.

Any Button On The Remote

  1. PRESS the button you want to clear - RELEASE
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  3. PRESS 9 - 9 - 4
  4. PRESS the button you want to clear twice. - Two blinks.

All Key movers,Macro's, and Defaults

  1. PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  3. PRESS 9 - 8 - 0 -- Two blinks.

Scrambled Keypad

Sometimes it seems that the keypad is "scrambled". Functions like channels, volume, or numbers are not where they should be.
If your remote seems to be acting this way, try the following proceedure:
  1. PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  3. ENTER 9-7-3 (two blinks) (for URC-2005, try 9-7-4)
  4. Try the functions on the remote
If the keypad continues to act "scrambled", you may:
  • Be on the wrong code for your device.
    A wrong code may only operate a few functions of your equipment or they may be operating inaccurately.
  • Have something more serious wrong with the remote.
In either case you will have to contact us for more information.

menu

Key Mover

An Advanced Function To A Button

  1. PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
  2. PRESS and HOLD the MAGIC button until the green LED flashes twice then RELEASE
  3. PRESS 9 - 9 - 4.
  4. PRESS the "MAGIC" button and then the three digit extended function.
  5. PRESS the button you wish to use for that function - Two Blinks.

From One Button to Another

  1. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  2. PRESS 9 - 9 - 4.
  3. PRESS the DEVICE and the FROM button
  4. PRESS the DEVICE and the TO button
  5. Two Blinks
EXAMPLE: To take the volume from a TV and put it in the VCR mode,
it would be: MAGIC - 9 - 9 - 4 -TV - VOL UP - VCR- VOL UP - two blinks.
You would have to do the same process for VOL DN and MUTE.

"Shifted" Key Mover

In order to stack a second function on a key; when pressing the button you want the function on in the sequence, instead hit MAGIC and then the button you want.
To use the function: TAP the MAGIC button and release, then TAP the key you chose.
FOR EXAMPLE:VCR-MAGIC(hold 2 blinks) 9-9-4 MAGIC 2-3-4 MAGIC PLAY
If you hit the PLAY button - the VCR will PLAY, if you hit MAGIC -PLAY it will bring up a display.

menu

Macro-Sequence

This will allow you do do several functions with just the touch of ONE key.
  1. PRESS and HOLD the MAGIC button until the green LED flashes twice, then RELEASE.
  2. PRESS 9 - 9 - 5
  3. PRESS the key you want the Macro to be on
  4. PRESS the sequence of keys you want the remote to do
  5. PRESS "MAGIC" and wait for two blinks - RELEASE.
When you hit the key you put the macro on it will automatically start the sequence.
IMPORTANT: The Macro key will be the macro in ALL MODES so it is best to pick a key you will not need for anything else in any other mode.

menu

How To Learn Functions

The Pro Producer 7 has 16 blank learning keys that can learn infrared signals from your original remote controls.
The keypad consists of 18 keys, the LEARN and SHIFT keys as well as the 16 blank learning keys.
The SHIFT key allows you to learn a total of 32 functions on the 16 blank learning keys.

TO LEARN A FUNCTION FROM YOUR ORIGINAL REMOTE

  1. PRESS and HOLD the LEARN key
    NOTE: The LED will not blink while you are holding the LEARN key
  2. While HOLDING the LEARN key, PRESS and RELEASE one of the blank learning keys.
    The LED will blink ORANGE and stay for 60 seconds to show that the remote is ready to learn a function.
  3. WHILE the ORANGE LED is blinking,
    HOLD the original remote less than six inches from the Pro Producer 7
  4. AIM the original remote control at the top of the Pro Producer 7
  5. PRESS and RELEASE the key on the original remote control that you would like to learm.
    NOTE:If the Pro Producer 7 learns the function, the LED will change color from ORANGE to GREEN, and blink GREEN twice.
    If the function is NOT learned, the LED will change from ORANGE to RED and blink RED twice.
  6. RELEASE the LEARN key

HOW TO LEARN FUNCTIONS USING THE SHIFT KEY

  1. PRESS and HOLD the LEARN key
    NOTE: The LED will not blink while you are holding the LEARN key
  2. WHILE HOLDING the LEARN key, PRESS AND HOLD the SHIFT key.
  3. While HOLDING the LEARN key AND the SHIFT key, PRESS and RELEASE one of the blank learning keys.
    The LED will blink ORANGE and stay for 60 seconds to show that the remote is ready to learn a function.
  4. While still HOLDING the LEARN key AND the SHIFT key, and WHILE the ORANGE LED is blinking,
    HOLD the original remote less than six inches from the Pro Producer 7
  5. AIM the original remote control at the top of the Pro Producer 7
  6. PRESS and RELEASE the key on the original remote control that you would like to learm.
    NOTE:If the Pro Producer 7 learns the function, the LED will change color from ORANGE to GREEN, and blink GREEN twice.
    If the function is NOT learned, the LED will change from ORANGE to RED and blink RED twice.
  7. RELEASE the LEARN and SHIFT keys
  8. To use the learned function, PRESS the SHIFT key and the learned key

menu


All Material Copyright Universal Electronics Inc.
"One For All" copyright Universal Electronics Inc.
Any questions about the products should be directed to help@ueic.com