JP1 Remotes

Hi.
I have a JU slingbox, and I'm unable to control my ADB model: ABQ-1H4G cable box.
A friend extracted the remote control IR codes for me with LIRC.
I hope that somebody here can help me on this.

Thanks
Ziv

# this config file was automatically generated
# using WinLIRC 0.6.5 (LIRC 0.6.1pre3)
#
# contributed by oren (fungis)
#
# brand: hot
# model:
# supported devices:
#

begin remote

name hot
bits 16
flags SPACE_ENC
eps 25
aeps 100

header 9009 4456
one 595 521
zero 595 1649
ptrail 595
repeat 8975 2249
pre_data_bits 16
pre_data 0xF3F3
gap 44448
toggle_bit 0


begin codes
power 0x000000000000FF00
vod 0x0000000000008F70
tv-gueid 0x0000000000007F80
Esc 0x000000000000CF30
LC 0x0000000000004FB0
Info 0x000000000000AF50
CH+ 0x000000000000EF10
CH- 0x0000000000006F90
red 0x00000000000057A8
green 0x0000000000009768
yellow 0x00000000000017E8
blue 0x000000000000E718
service 0x0000000000003FC0
lng 0x000000000000B34C
mail 0x000000000000FD02
1 0x0000000000006798
2 0x000000000000A758
3 0x00000000000027D8
4 0x000000000000C738
5 0x00000000000047B8
6 0x0000000000008778
7 0x00000000000007F8
8 0x000000000000FB04
9 0x0000000000007B84
0 0x000000000000BB44
fav+ 0x000000000000F30C
fav- 0x000000000000738C
up 0x0000000000000FF0
down 0x0000000000007788
right 0x00000000000037C8
left 0x000000000000B748
select 0x000000000000D728
score 0x000000000000BD42
camera 0x000000000000BF40
magic 0x0000000000007D82
hot-active 0x000000000000DF20
stop 0x000000000000F10E
rew 0x000000000000718E
play 0x000000000000B14E
pause 0x00000000000031CE
ff 0x000000000000D12E
rec 0x00000000000051AE
end codes

end remote

zivayalon wrote: I hope that somebody here can help me on this.

With reading the LIRC file? Or with using RemoteMaster to produce the Slingbox file?

I'll assume you mean the first. There are instructions around here somewhere for the second.
If I'm reading that right, it means protocol=NEC1, Device=48, Subdevice=48

All that info goes on the setup sheet in RemoteMaster, along with other info (see instructions elsewhere).
Then to fill in the Functions sheet of Remotemaster, you find or type each function name in the "Name" column, then in the "Hex" column you type the two characters before the last two from each of the LIRC lines, so FF for power and 8F for vod.

After the functions sheet is done, you need to assign things on the buttons sheet, which is part of the everything other than reading the LIRC file, in those instructions I mentioned.

I found some of those instructions, so I'll comment on how your use should fit those instructions:

Start at page 3 of the instructions, because you are getting info from LIRC, not from a learning JP1 remote.

Steps 3.4 to 3.6, use the info I provided above.

Step 3.8, instead type in the two character "Hex", and RM will compute the OBC, etc. for you. Also if you can't find the function name you want in the "Name" column type over some name you don't need. The names initially there are just suggestions.

Somewhere around Step 3.16 (maybe it's there and I missed it) you should use the file/save command to save your work as an .rmdu file. Just saving it as .bin files doesn't give you quite everything you would need to pick up editing it later, in case you need to fix some detail and/or share the results.

With reading the LIRC file? Or with using RemoteMaster to produce the Slingbox file?

I need it for RemoteMaster to produce the Slingbox file.

Thanks for the instructions I'll try it out and let you know.

Ziv