Page 1 of 2
Digiturk DCR OPTV 3900 codes ?
Posted: Wed Nov 08, 2006 2:46 pm
by ozcet
Hi, I need the binary upgrade file for the turkish satelite tv provider's new set-top-box. The remote uses xmp protocol and is a product of UEI (omega). Thank you in advance..
http://investor.uei.com/phoenix.zhtml?c ... &highlight
http://www.uei.com/category.php?page_id ... product=31
Posted: Wed Nov 08, 2006 8:56 pm
by The Robman
I will try to get the right info from UEI.
Posted: Thu Nov 09, 2006 10:16 pm
by The Robman
Posted: Fri Nov 10, 2006 8:39 am
by ozcet
Rob,
Thank you for the file. But I was unable to load the compiled binary file to slingbox. I am using 2 slingboxes. 1 US version with IR Blaster 2 and second UK version IR Blaster 4. While loading I got the error code 0x93260001. Could you compile and send these two binary files, maybe I am doing something wrong. I tried 3 RDF files PL, JU, RV on both slingboxes. Thank you again..
P.S: I am using RM 1.69, Slingplayer 1.3.0176
Posted: Sun Nov 12, 2006 6:58 pm
by The Robman
Apparently there was a minor issue with RM. Greg has created a new version of the upgrade that you can use here...
https://www.hifi-remote.com/forums/dload ... le_id=3844
I have converted the upgrade into bin files (for all 3 versions of the SB) here:
https://www.hifi-remote.com/forums/dload ... le_id=3845
Give it a shot.
It's OK
Posted: Mon Nov 13, 2006 2:03 pm
by ozcet
Thank you Rob, it works perfect. You can put the files on your file section.
regards,
Posted: Sat Dec 16, 2006 7:40 am
by bkerem
Hello,
I have the digiturk remote which I do not want to use.
But I also own a UEI One For All (UCR-9960).
I need the code of the digiturk's remote for to enter to my One For All remote.
Does anyone knows?
Pleased to hear,
B.Regards
B.Kerem
Posted: Sat Dec 16, 2006 8:53 am
by The Robman
bkerem wrote:Hello,
I have the digiturk remote which I do not want to use.
But I also own a UEI One For All (UCR-9960).
I need the code of the digiturk's remote for to enter to my One For All remote.
Does anyone knows?
Pleased to hear,
B.Regards
B.Kerem
The upgrade code is listed a few posts above yours.
thx
Posted: Sat Dec 16, 2006 11:01 am
by bkerem
Thanks for your pompt relpy The Robman,
I have already tried to enter 1431 to my remote. But it did not work out.
There are some flinks for files at the topc about this remote. I have downloaded them but, they are not the files that I can understand.
If u have time, may you pls help me?
Thanks in advance,
Regards
B.Kerem
Posted: Sat Dec 16, 2006 12:32 pm
by The Robman
I'm guessing that you don't realize what this forum is for. This forum is for JP1 users. JP1 is the process that you can use to load new codes into your remote.
U r right
Posted: Mon Dec 18, 2006 2:40 am
by bkerem
Hi Robman,
You are right... I found this forum by searching from Google. After reading more topics I understand that I need a JP1 cable for my OFA URC-9960 Kameleon remote. Also I found out that the connection to my remote also needs a modification as there aren't any pins, only 6 pads which I need to solder pins or buy some adaptor to fit on it.
My latest notebook does not have a serial port. Guess I guess a USB cable is much better when we think for future.
I have just ordered and USB jp1 cable from diygadget.com. But they do not have a pogo adaptor. Hope I can arrange something.
Now I will read more to find out how I will programme my remote.
Regards
B.Kerem
Posted: Mon Dec 18, 2006 12:49 pm
by The Robman
If you don't have a pogo-pin adapter, you should attempt to solder a 6-pin connector onto the pads. Most JP1 vendors include a free 6-pin with the cables that they sell, so you probably already have the 6-pin so all you need to do is solder it.
This post might help with the soldering...
https://www.hifi-remote.com/forums/viewt ... 1595#p31595
Remember also that your URC-9960 has a modem built in, so you can load upgrades into it with a JP1 cable if you use the JP1 tools to convert the upgrades into WAV files.
Thanks
Posted: Tue Dec 19, 2006 1:59 am
by bkerem
Thanks for the information Robman,
I will try to solve it out by reading this forum when I receive my cable.
Thanks for your help.
Regards
B.Kerem
Connected to remore but can not load codes
Posted: Sun Jan 21, 2007 3:00 pm
by bkerem
Hi Again,
I got my USB cable. and solder 6 pin to my kamaleon remote.
I manage to connect my remote (UEI One For All (UCR-9960))
Still try to load code for sat.digiturk.
Tried to files which I downloaded from above mentioned links with IR program.
Form files, I shoce open and fallow on screen insturctions but got error code every time.
Can u help me?
Pleased to hear,
B.regards
B.Kerem
Re: Connected to remore but can not load codes
Posted: Sun Jan 21, 2007 3:15 pm
by Mark Pierson
bkerem wrote:got error code every time.
You'll need to be more specific. What program are you using and what are the error messages?