JP1 Remotes

[GOGGS75]

In trying to set up an upgrade for a Digital TV Receiver I discovered that although the Nokia 32 is a recognised protocol on IR615 in does not exist on Keymap Master v8.33 or Remote Master according to another member of the group having the same problem.

I have read the Keymap master Protocols text file but cannot see where to start analysing the learned signals for the Nokia 32 protocol I have in the diagnosis area http://www.hifi-remote.com/forums/dload.php?action=file&file_id=1986 as I am only a beginner.

Is it better to attempt to create the protocol myself or leave this to an expert.

Thanks for any help.


_________________
GOGGS75

[Capn Trips]

John Fine has addressed this by searching the forum for you in your earlier thread:

[Capn Trips]

To save you some more trouble, here is the protocol from the device file built in the thread referenced above:

48 93 32 8B 16 CF 01 08 08 00 00 00 3F 00 53 00
77 C4 52 00 D2 00 76 FF FF FF 04 77 77 8D 01 46

and here is the protocol decoded from a UEI-provided Nokia32 device upgrade from further down that thread:

Protocol:

47 93 41 8B 15 00 00 54 00 77 00 54 00 CA 00 54
01 1D 00 54 01 71 00 D0 00 77 A6 0D 02 EB 03 E6
0D 12 76 03 01 6B 08 76 00 01 6B 03 B6 06 80 F6
FF 56 6C 09 F6 01 0A FB 0B C6 F8 13 88 F6 01 58
6A F2 8B EB 76 03 02 EB 01 AF C6 F8 13 88 F6 01
58 6A F7 46 06 80 1C 22 F6 01 4C B0 C4 87 34 04
F6 FF 6C 4E 37 44 F6 1C 12 8D 01 4C 5C 04 90 C3
90 C3 08 C3 56 C0 03 86 04 C0 06 C1 12 F6 01 4C
5A EC AF

I'm no expert, but I believe you can give the protocol any ID you want, e.g 01 EE (so long as it doesn't conflict with any other protocol you want your remote to access)

[GOGGS75]

I have started to create an upgrade from the UEI provided NOKIA 32 device upgrade. This is now in the diagnosis area.

http://www.hifi-remote.com/forums/dload.php?action=file&file_id=1993

I am still looking for some of the data that seems relevant (???) and was hoping someone could help.

The development so far has been as follows:

PROTOCOL TABLE

Protocol name = Manual Settings
Device 1 no. = ???
Device 2 no. = ???
Device 3 no. = ???
Raw Fixed Data = ???


MANUAL SETTINGS

PID = 01 90 (slightly higher than the highest PID on display)
2nd Cmd Byte = ???
Signal style = ???
Bits/Dev = ???
Bits/Cmd = ???


3RD PARTY PROTOCOL CODE

Copied UEI upgrade code in format shown under protocol help.. Selected
1 = 01 90, not sure if this is correct.[/url]

Thanks for any help
_________________
GOGGS75

[GOGGS75]

Reading the initial thread right through rather than following a link on this I managed to find a link to a Keymaster text file set up for the Galaxis Satellite Box applying a custom made Nokia 32 protocol.

Link: http://www.hifi-remote.com/forums/dload.php?action=file&file_id=1065

Using this I managed to set up a Keymap master text file for the Matsui Digital TV Receiver and copied this to IR successfully. This is working successfully on the URC8910. I have put a copy of the file in the Upgrade area of the files section as this will help others looking for the Nokia 32 protocol.

Link: http://www.hifi-remote.com/forums/dload.php?action=file&file_id=1995

I could not understand how the IR615 learned signals relate to the 4 character hex code shown on Keymap master but am happy it works.


_________________
GOGGS75

[dsarens]

Great work GOGGS75

I've got it to work with my URC7541 using your file. There are three buttons missing (swap, wide and status). I'm going to see if I can find a pattern between the learned EFC/OBC codes and the resulting 4-byte hex command.

Thanks for all your hard work!

[dsarens]

I've got a bit further with the missing functions. Using the info in the link earlier in this thread
http://www.hifi-remote.com/forums/viewtopic.php?p=21195#21195 I've translated two of three functions successfully;

Status=obc 3Fh becomes 77 77

Wide=obc 61h becomes B2 FF

and they both work, but

Swap=obc FFh becomes EE EE which doesn't work. The OBC of FFh seems a bit odd as all the other functions are between 00h and 78h, but this is what the learned function is showing.

GOGGS75 - do you also get FFh when you learn the swap function?

[GOGGS75]

Dsarnes,

I also get the hex code FF when learning the swap function.
_________________
GOGGS75

[dsarens]

Swap function DOES work as EE EE

I had a pesky key move programmed in that I'd forgotten about

[The Robman]

Good work guys. Make sure that one of you loads an updated upgrade file for this device with the additional functions that you found.
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!