Page 1 of 1
Trouble creating BIN file using MCE protocol.
Posted: Wed May 20, 2009 5:42 pm
by Digital Larry
Target device = Moxi HD DVR.
Target chip = UEI PL or Axum (used on HAVA, similar to SlingBox)
IR 7.14 decodes the protocol just fine.
MCE
Device 8
Subdevice 57
Misc T = 1
Over in Remote Master 1.86, choosing MCE protocol gives me the option to enter
Device
OEM2
Well I put 57 for OEM2 since I couldn't think of what else to do... but the resulting codes from my HAVA (a) don't work, (b) decode as "garbage" through the URC8910/IR combination.
Hints?
Posted: Wed May 20, 2009 7:37 pm
by The Robman
Post your IR file, with the learned signals in it, so we can take a look.
Posted: Wed May 20, 2009 8:38 pm
by mdavej
No need to reinvent the wheel. There are several Moxi upgrades and slingbox files in the file section.
Posted: Thu May 21, 2009 3:55 pm
by Digital Larry
All of the available Moxi codes apparently are for their older boxes. The latest ones use MCE protocol.
I've posted my IR files here:
https://www.hifi-remote.com/forums/dload ... le_id=6747
Basic question though - IR shows Device and Subdevice for MCE protocol. Whereas RM shows Device and OEM2. Does that make any sense?
I also tried fiddling with the RC6-m-32 but also without luck.
I got this info from the guys at Digeo:
https://www.hifi-remote.com/forums/dload ... le_id=6748
Thanks!
DL
Posted: Tue May 26, 2009 1:18 pm
by Digital Larry
I did this exercise again using the most recent software:
IR.exe 8.00
and
RemoteMaster 1.93...
But the end result is the same.
Posted: Wed May 27, 2009 11:02 am
by Digital Larry
***DOOFUS ALERT***
***DOOFUS ALERT***
Hi Kids,
Just reporting back on my sad but exaggerated tale of woe. Turns out that my BIN file works just fine. I was lacking the actual device to test so I was trying to capture the codes from the HAVA IR blaster cable to compare to the original. I guess what's happening is that the HAVA blaster output is quite a bit lower than with a handheld remote (which makes sense as it's supposed to work from 1-2 inches away rather than 15 feet).
So now I can confirm that as far as I can tell, MCE protocol attribute "OEM2" in RM corresponds to "Subdevice" as reported by IR.exe.
Over and out!
Posted: Wed May 27, 2009 1:34 pm
by The Robman
I've tried capturing from the Slingbox IR blaster and have never been able to do so, so I understand.
Posted: Fri Jun 19, 2009 10:19 am
by houdini
Hey Larry, can you post your RM file for the moxi hd 3012 dvr that you got? I just got mine installed today and I'm trying to set up my slingbox. I guess I need to create a bin.
I did a search and didn't find the file. If I've missed it please link me!
Thanks
Posted: Fri Jun 19, 2009 1:16 pm
by The Robman
Posted: Fri Jun 19, 2009 2:01 pm
by houdini
Thanks Rob but those are the old MOXI dvr bins right?
I have the new Moxi hd 3012 dvr. I see that Larry posted IR files and possibly the pronto file. I was hoping to get the RM file he made so I could generate a PL slingbox bin.
Posted: Fri Jun 19, 2009 3:16 pm
by The Robman
I just built this RM file based on the learns that DL posted earlier, give it a try...
https://www.hifi-remote.com/forums/dload ... le_id=6866
Posted: Sat Jun 20, 2009 9:30 pm
by houdini
Thanks Rob. Works like a charm
