JP1 Remotes Forum Index JP1 Remotes


FAQFAQ SearchSearch 7 days of topics7 Days MemberlistMemberlist UsergroupsUsergroups RegisterRegister
ProfileProfile Log in to check your private messagesLog in to check your private messages Log inLog in

Set up code for a hex code

 
Post new topic   Reply to topic    JP1 Remotes Forum Index -> JP1 - General Forum
View previous topic :: View next topic  
Author Message
kdp99



Joined: 04 May 2004
Posts: 40

                    
PostPosted: Tue Aug 13, 2024 2:45 am    Post subject: Set up code for a hex code Reply with quote

I am trying to find a set up code (or what device name, etc),uses this IR data ?

Not sure if its even possible ? Any advice welcome

RC6-M-28: {D=0,F=44,M=6,S=2070}, beg=0, end=57, reps=1

Typical Hex

0000 0073 0000 001D 0060 0020 0010 0010 0010 0010 0010 0020 0010 0020 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0020 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0020 0020 0020 0010 0010 0020 0010 0010 0010 0010 0020 0020 0020 0010 0010 0020 0010 0010 0010 0E10
Back to top
View user's profile Send private message
The Robman
Site Owner


Joined: 01 Aug 2003
Posts: 21519
Location: Chicago, IL

                    
PostPosted: Tue Aug 13, 2024 8:55 am    Post subject: Reply with quote

This is a very low-level question and I'm guessing it's for a much higher-level problem. If I were to ask you WHY you wanted to know this, I'm betting that your answer would be "because I want to program my remote to work by XYZ device", am I right? In which case, if you just said that, we might already have an upgrade for it. Providing the hex code would be a clue in such a case, not the only piece of information provided.

If you're trying to program a Sky Q box, we have an upgrade here:
http://www.hifi-remote.com/forums/dload.php?action=file&file_id=14577
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
Back to top
View user's profile Send private message Visit poster's website
kdp99



Joined: 04 May 2004
Posts: 40

                    
PostPosted: Tue Aug 13, 2024 11:13 am    Post subject: Reply with quote

Sort of. Its for the Sky streaming device, Sky Stream, the device is a puck and the Sky Q codes do not work.

I have found this protocul, and generated all 256 codes for it and am working through them.

I though if there was a device set up code that used this protocul it might be quicker.

The reason for all this is the Sky Puck remote is very basic with very few buttons. I have found with some other devices there are remote options that work the device that are not on the orignal remote and are quite convenient.
Back to top
View user's profile Send private message
The Robman
Site Owner


Joined: 01 Aug 2003
Posts: 21519
Location: Chicago, IL

                    
PostPosted: Tue Aug 13, 2024 12:06 pm    Post subject: Reply with quote

Are you a JP1 user, with a JP1 remote and cable? If so, when you say "the Sky Q codes do not work", do you mean the built in setup codes, or do you mean the Sky Q upgrades in the file section?
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
Back to top
View user's profile Send private message Visit poster's website
mdavej
Expert


Joined: 08 Oct 2003
Posts: 4605

                    
PostPosted: Tue Aug 13, 2024 12:34 pm    Post subject: Reply with quote

Also relalize that once you load the partially working upgrade you made, you can still send manual EFCs if you prefer to test that way. That's as good as any built in code.
Back to top
View user's profile Send private message
kdp99



Joined: 04 May 2004
Posts: 40

                    
PostPosted: Tue Aug 13, 2024 1:03 pm    Post subject: Reply with quote

The Robman wrote:
Are you a JP1 user, with a JP1 remote and cable? If so, when you say "the Sky Q codes do not work", do you mean the built in setup codes, or do you mean the Sky Q upgrades in the file section?


I have a JP1 remote and cable but its not been used for a while. I came back to 'pick some wise brains'

I used the Sky Q set up code from URC / CCP of 240. ( I was originally getting Sky Q not Sky Stream but that a long story ...). CCP has a JP1 section but this does not have Sky Q.

I found these codes did not work the Puck. There was one code that did DVR or similar turned it on.

This makes me wonder if Q and the Puck use the same protocul but different codes within it and DVR is the one overlap ?

I am part way through testing the 256 codes, but have found 0-9 are the number buttons 0-9.

Thanks for the ideas so far.
Back to top
View user's profile Send private message
The Robman
Site Owner


Joined: 01 Aug 2003
Posts: 21519
Location: Chicago, IL

                    
PostPosted: Wed Aug 14, 2024 8:08 am    Post subject: Reply with quote

If you're not using your cable, how are you testing anything? I can't help but think you're making this really hard for yourself, but hey, if you're enjoying doing what you're doing, have at it.

But if you've already found that OBCs 0-9 work the number buttons 0-9, then so far, you've confirmed that the upgrade that I linked you to is correct.
_________________
Rob
www.hifi-remote.com
Please don't PM me with remote questions, post them in the forums so all the experts can help!
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic       JP1 Remotes Forum Index -> JP1 - General Forum All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


 

Powered by phpBB © 2001, 2005 phpBB Group
Top 7 Advantages of Playing Online Slots The Evolution of Remote Control