Scientific Atlanta KMM3000 TM codes

mq109 · Post by **mq109** » Fri Jan 30, 2009 4:59 pm

I have a slingbox pro, how can I do to work's witch ir on my scientic atlant kmm3000

Thank you for my attention.

Post by **The Robman** » Fri Jan 30, 2009 6:33 pm

We haven't seen the Scientific Atlanta KMM3000 here yet, so we don't have the codes. I did a Google search and found a post over in the Sling community where someone has captured the codes, so hopefully they will post the info over here.

http://www.slingcommunity.com/forum/thr ... -TM-codes/

mq109 · Post by **mq109** » Fri Jan 30, 2009 6:36 pm

Robman, thank's for your information.
See you

alanrichey · Post by **alanrichey** » Sat Jan 31, 2009 1:21 am

That would be me

Unfortunately I am a bit of a novice at this, and when none of the codes were recognised by IR.EXE as a specific Protocol and device I gave up. If an expert wants me to try anything else please let me know.

Later: For Robman. Just saw your post on the Sling Community forum. Happy to help. I have the SA 3000 installed on my Harmony Remote control and I have a JP1 URC 8910 and IR.EXE

What do you need ?

Al

Post by **The Robman** » Sat Jan 31, 2009 8:50 am

Hi Al, thanks for coming over here. Could you learn the signals from the Harmony using your URC-8910, then verify that the learns on the 8910 actually work. Then download the memory using your JP1 cable and save the IR file. (If the memory fills up, after you've downloaded, delete all the learned signals and learn the rest of the buttons and save a 2nd file).

Then, load your IR file(s) into the Diagnosis Area:
http://www.hifi-remote.com/forums/dload ... &cat_id=35

and post a link to them here, then I'll do the rest.

alanrichey · Post by **alanrichey** » Sat Jan 31, 2009 10:11 am

Hi Rob

I can't verify the codes as I don't have access to the box, all I can do is learn them from the Harmony. And this is going to take some time as the remote fills up after about 6 codes. And to my untutored eye it looks like rubbish

And there are warnings about more than 3 burst codes ?

I have uploaded the first file with codes for Power, Menu, Guide and the navigation keys at http://www.hifi-remote.com/forums/dload ... le_id=6188

Can you take a quick look and see if it is feasible ? if so I will do to the rest of the codes.

Al

Post by **The Robman** » Sat Jan 31, 2009 10:46 am

Yup, those are good enough for me to construct an upgrade from, so please continue. (Could you re-learn the LEFT button please).

What learning technique are you using? Are you holding the Harmony button down until the 8910 reads SUCCESS? If you're not, try it that way. If you are, try using short presses of the Harmony remote instead.

When you hold the harmony button down, the complete signal repeats, which normally causes the 8910 to learn just one copy and flag it as repeating (which is good) but in this case you're actually storing multiple copies of the data. This could be caused by you releasing the Harmony button too soon, or maybe the Harmony itself stops sending.

A short press of the Harmony button will hopefully cause just one repeat to be stored by the 8910 which would let you store more buttons in each cycle.

Post by **vickyg2003** » Sat Jan 31, 2009 11:17 am

Rob,

What does "Phase Encoded (RC Type)" mean?

alanrichey · Post by **alanrichey** » Sat Jan 31, 2009 11:27 am

The Robman wrote:Yup, those are good enough for me to construct an upgrade from, so please continue.
A short press of the Harmony button will hopefully cause just one repeat to be stored by the 8910 which would let you store more buttons in each cycle.

Did that and got a lot more in

Have uploaded the files at http://www.hifi-remote.com/forums/dload ... le_id=6189

File 1 is the one you already have.
File 2 is the new left key and all the rest except Stop
File 3 has Stop and 3 other commands learned onto 1,2,3
1. Replay
2. Advance
3. Cancel

For some reason the Pause button doesn't seem to be supported (no IR code transmitted). Don't suppose you can interpolate can you ?

Let me know if you need any more codes refreshed.

Cheers

Al

Post by **The Robman** » Sat Jan 31, 2009 11:54 am

They're all good except for two, could you re-learn 4 and Replay. Thanks.

alanrichey · Post by **alanrichey** » Sat Jan 31, 2009 12:09 pm

The Robman wrote:They're all good except for two, could you re-learn 4 and Replay. Thanks.

Done, file at http://www.hifi-remote.com/forums/dload ... le_id=6190

The Replay is mapped to "2"

Al

Post by **The Robman** » Sat Jan 31, 2009 12:15 pm

The 4 learn still isn't good enough, could you try learning it several times so there's a better chance of there being at least one good sample.

alanrichey · Post by **alanrichey** » Sat Jan 31, 2009 12:42 pm

File is at http://www.hifi-remote.com/forums/dload ... le_id=6192

ALL the numbers keys are learned as "4", hopefully one is OK

Al

Post by **The Robman** » Sat Jan 31, 2009 2:03 pm

Thanks Al, I got them all now.

MG, here's a PL Slingbox upgrade for you to try...
http://www.hifi-remote.com/forums/dload ... le_id=6191

mq109 · Post by **mq109** » Sun Feb 08, 2009 12:34 pm

Robman, today I testing your C2000_PL.bin, but it didn't work, it was feather..