Codes? General Instrument 350i ku/C analog Sat rcvr

Hulkinator · Post by **Hulkinator** » Wed Jun 13, 2007 9:05 am

Loaded up and tested away and the only button that would do anything obvious was Num5 that toggled H/V. I imagine this is POL button on original remote. Assigned it to (cc) button on URC-6692 remote and reloaded the changed 554 file. Works.

I think some "skew" and other motor control buttons might be in the testing file as the dot under the 2 digit channel display blinks (receiving something) but I dont have a C band setup connected to this right now...

Looks like we are still missing a few buttons/functions...any ideas...?

I think original remote could be this :

http://impaktproducts.com/product.php?p ... 268&page=1

Thanks

Post by **The Robman** » Wed Jun 13, 2007 10:03 am

I have a request into UEI for a complete EFC list for the SAT/0554 setup code. If I get a response I'll post the updated list.

Post by **The Robman** » Wed Jun 13, 2007 11:26 am

Here are the OBCs that we already know...
016 - num 0 / ? (can't read letter)
071 - num 1 / G
066 - num 2 / T
029 - num 3 / F
072 - num 4 / E
067 - num 5 / M
030 - num 6 / C
014 - num 7 / S
007 - num 8 / R
000 - num 9 / K
031 - Vol UP
068 - Vol DOWN
068 - MUTE
024 - Channel UP
025 - Channel DOWN
021 - POWER
065 - ENTER
028 - CLEAR
009 - POL

023 - PIP (view)
022 - MOVE (next)
004 - MENU UP (audio up)
003 - MENU DOWN (audio down)
027 - MENU (setup)

From the remote picture, these are the functions still to be found...
text
help
setup
next
message
view
c/kU
pol
Skew+
Skew-
prog
call
video east
video west
audio <
audio >

Post by **The Robman** » Thu Jun 14, 2007 11:41 am

I've got good news and bad news. The good news is that UEI has sent me the complete list of codes for SAT/0554, so I have updated the KM file...

http://www.hifi-remote.com/forums/dload ... le_id=4653

The bad news is that all of these new codes were part of the test upgrade that I created for you, so if the codes were going to work, you would have found them when you tested it.

Hulkinator · Post by **Hulkinator** » Fri Jun 15, 2007 6:19 pm

Hmmm could this be tougher because I am using a URC 6692 B00 and everything says 6690...how different are these....? i think not much...

I loaded up the 554 code and still look like its missing the all important SETUP button...

Thanks

Post by **The Robman** » Fri Jun 15, 2007 7:19 pm

Hulkinator wrote:I loaded up the 554 code and still look like its missing the all important SETUP button...

SETUP is EFC 251, OBC 27 and it's assigned to the MENU button.

Hulkinator · Post by **Hulkinator** » Sun Jun 17, 2007 1:23 pm

Pressing MENU does not access the OSD menus on the 350i. Nothing happens. I can see the remote is transmitting but no reaction from the receiver...everything else seems to work. This is odd...

Thanks

Post by **The Robman** » Sun Jun 17, 2007 2:03 pm

My suggestion would be to re-try the experimental upgrade that I created earlier as all of the new button codes that I was given were present in that upgrade.