if support panasonic tz-dch1100 ?

siulungchow · Post by **siulungchow** » Thu Dec 25, 2014 7:38 am

as title，i try all in list，but not work⋯

alanrichey · Post by **alanrichey** » Sat Dec 27, 2014 7:42 am

Is this any good ??

http://www.hifi-remote.com/forums/dload ... e_id=13011

siulungchow · Post by **siulungchow** » Sun Dec 28, 2014 3:43 am

sir

thanks for upload Panasonic TZ-DCH1100 bin file, but this version not work, even power key also not work, if passable have any solution ?

alanrichey · Post by **alanrichey** » Sun Dec 28, 2014 6:54 am

First, please read the instructions properly, it SPECIFICALLY states that 'does not work' is not an acceptable reply. Please do what they say.

siulungchow · Post by **siulungchow** » Tue Dec 30, 2014 4:18 am

Sir,

Sorry for any offend, here is my test result

1. What model Slingbox do you have? -> Slingbox solo

2. Was there any error message after you typed in the Code and tapped the Test button?　－＞ｎｏ，　ｏｎｌｙ　ｎｏ　ｒｅｓｐｏｎｓｅ　ｗｈｅｎ　Ｉ　ｃｌｉｃｋ　ｔｈｅ　ｂｕｔｔｅｎ

3. Did you give the commands plenty of time to react? (I have a DVR that takes about 6-8 seconds to power up/down)　＾＞　ｙｅｓ，　ｉｔ‘ｓ　ｓａｍｅ

4. If you are using a Solo did you try both BIN files?→　ｙｅｓ
5. After completing the setup do any of the buttons work?　－＞　ｎｏ　ａｎｙ　ｂｕｔｔｏｎ

6. If you are installing on a Solo or Pro-HD or older box that uses an external IR Blaster, have you used a Digital Camera or Mobile Phone Camera to confirm the IR Blaster is actually firing when you tap the Power button? (Watch the tip of the IR Blaster through the viewfinder while you tap a button. You should see a white (not red) flash. Test it on a real remote so you know what you are looking for). If you are using a 350/500 have you tried using the external blaster?　－＞　Ｎ／Ａ

7. Have you experimented with the placement of the IR Blaster? On some devices this is critical so don’t give up too quickly. Try shining a flashlight at the front of the receiver and see if you can see the IR receiver behind the smoked glass.　ー＞　ｙｅｓ

8. Are you sure the device is working correctly using the real remote?　－＞　ｙｅｓ
9. Are you sure your device is set to use IR ? Many boxes can operate on RF or IR and if it is set to RF then the Slingbox will not affect it.　－＞　ｙｅｓ
10. If you have a device that supports multiple －＞　Ｉ　ｔｒｙ　ｔｏ　ｕｓｅ　ｉｎ　ｓｌｉｎｇｂｏｘ　ｃｌａｓｓｉｃ，Ｉｔ‘ｓ　ｗｏｒｋ，　ｓｏ　Ｉ　ｔｈｉｎｋ　ｔｈｉｓ　ＢＩＮ　ｆｉｌｅ　ｈａｖｅ　ｓｏｍｅ　ｉｓｓｕｅ　ｉｎ　ｓｏｌｏ　ｖｅｒｓｉｏｎ

alanrichey · Post by **alanrichey** » Tue Dec 30, 2014 5:53 am

Q6 is not N/A, it is ABSOLUTELY ESSENTIAL you check the IR Blaster is firing, or we are both wasting our time.

And ALL Slingboxes use the same BIN file, so if it works on your Classic it will work on your Solo. Which again points to the IR Blaster.

siulungchow · Post by **siulungchow** » Wed Dec 31, 2014 8:36 am

sir

Regarding #6, i can not see IR flash white light in solo ,ｂｕｔ　ｗｈｅｎ　Ｉ　ｓｗｉｔｃｈ　ｂａｃｋ　ｔｏ　Ｃｌａｓｓｉｃ，　ａｌｌ　ｂｕｔｔｏｉｎ　ｃａｎ　ｎｏｔ　ｕｓｅ　ｎｏｗ，　ａｌｓｏ　ｎｏ　ｗｈｉｔｅ　ｌｉｇｈｔ　ｗｈｅｎ　ｉ　ｃｈｅｃｋ　ｖｉａ　ｃａｍａｒａ（ｂｕｔ　ｉｔ　ｗｏｒｋｓ　ｙｅｓｔｅｒｄａｙ）

alanrichey · Post by **alanrichey** » Wed Dec 31, 2014 9:24 am

OK, you have a hardware problem then, nothing to do with the Custom Remote. Check all the cables are properly seated.

siulungchow · Post by **siulungchow** » Sat Jan 03, 2015 9:31 am

Sir,

I change a new IR CABLE and test In classic ,it's can switch channel now, but not flash light when I view via camera.

When I switch to solo, still can not switch channel, also no flash light . Can you please help me what's problem I have.

alanrichey · Post by **alanrichey** » Sat Jan 03, 2015 11:51 am

Sorry, no. I know that all Slingboxes use the same BIN codes so if it works on your Classic then it must be correct. I have no idea why it doesn't work on the Solo (unless you are installing the wrong BIN file ?

Yoiu say you have tried both files, but also reported no error messages ? That cannot be true, one of the BIN files will report as Invalid.

siulungchow · Post by **siulungchow** » Sat Jan 03, 2015 9:03 pm

Thanks lot!! I will try other model for verify .

alanrichey · Post by **alanrichey** » Mon Jan 12, 2015 11:19 am

As this Remote worked on the Classic I think I will release it for other users.

siulungchow · Post by **siulungchow** » Mon Jan 12, 2015 9:33 pm

Sir，

I would like ask how to change image of remote control, This version using basic image but it's different with current ,

Panasonic controller type is this one :
http://www.jcom.co.jp/library/stb/image ... 100_02.jpg

alanrichey · Post by **alanrichey** » Tue Jan 13, 2015 3:23 am

We can do this but ONLY if Sling have already designed the image for you. So if you can find a built-in remote that displays the correct image, even if it doesn't work, then I can do it for you.

siulungchow · Post by **siulungchow** » Tue Jan 27, 2015 12:45 pm

sir , the Panasonic tz-bdt910f image is same, If passable to use this ?

[/code]